×
Quick Used Equipment Filter












used search tag
0
Total: $0.00
    Nothing In Your Cart...
Go to Cart

See All Locations

RD45F HYDRAFLEX DRAPER

HydraFlex™ Draper

  • Harvest crops as close as possible to the ground with the HydraFlex™ cutterbar
  • Minimize grain loss with a two-speed center feed section
  • Enable higher harvesting speed without sacrificing cut quality with a 4” double cut, dual drive, shaft driven cutterbar
  • Get more done by eliminating header calibrations

Apply For Financing




Features



Optimize feeding with a two-speed center feed section, increased feed drum torque, and center crop flow divider

Overview

Increase grain in the tank with a two-speed center feed section. A slow-speed setting softens the impact of crop fingers and drum flighting when engaging with crop. This ensures that easy-shelling crops like lentils and soybeans do not get thrown over the feeder house. Use the high-speed setting in canola or high-yielding cereals to prevent slug feeding while ensuring that the drum does not plug.

Benefits
  • Experience less downtime during harvest related to unplugging the header, which allows for more harvesting time at the highest productivity levels.
  • Higher feed drum torque is matched to the capacity of the combine to ensure optimal feed rates into the combine. Higher torque on the front feed drum allows operators to confidently harvest tough feeding crops like canola.
  • Additionally, prevent underfeeding in light crops with the center crop flow divider. When not harvesting crop with the full width of the draper, the center crop flow divider prevents crop from skipping over the center feed section and going on the opposite draper belt.
Toolless shifting on the gearcase Toolless shifting on the gearcase
Center crop flow divider Center crop flow divider
Additional details
  • The two-speed center feed section maintains a consistent ratio between the feed drum and center feed belt speed.
  • Change center feed section speed with a toolless, two-speed, easy-shift handle on the gearcase to the left of the draper feeder house opening.
Two-speed center feed section (A is pulled out and B is pushed in) Two-speed center feed section (A is pulled out and B is pushed in)
Parts of the two-speed center feed section Parts of the two-speed center feed section
  1. Feed  drum gearbox
  2. Center feed drive shaft
  3. Knife drive shaft
  4. Center feed speed control
  5. Oil check
  6. Main gearbox
  7. Center belt gearbox
  8. Oil check

 

Low speed

High speed

Feed drum

200 rpm

240 rpm

Center feed belt

1000 rpm

1200 rpm

 

 

RDF

HDR

Feed drum torque

1217 lb-ft (1650 Nm)

2109.4 lb-ft (2860 Nm)

Center belt width

70 in. (177.8 cm)

79.1 in. (200.9 cm)

Superior ground following with the HydraFlex™ draper system

Overview

Achieve superior ground following when harvesting in a wide range of terrains, crops, and conditions with RDF HydraFlex Draper Platforms. HydraFlex is an industry-exclusive hydraulic float system.

HydraFlex draper system floats with the terrain HydraFlex draper system floats with the terrain
Benefits
  • Float closely to the ground over changing conditions by controlling the cutterbar ground pressure from the cab – simply adjust the armrest knob to vary hydraulic pressure in the float arm hydraulic cylinders.
Hydraulic float arm Hydraulic float arm
Adjust ground pressure by changing hydraulic pressure in the float arm cylinders Adjust ground pressure by changing hydraulic pressure in the float arm cylinders
Additional details
  • The hydraulic float system features a 7.5-in. (19-cm) float range.
  • To lock out the HydraFlex draper into rigid mode, the operator should increase the float pressure to maximum

Evenly feed canola and field peas into the feeder house with RDF top augers

Overview

Help bushy crops, especially heavy canola, feed evenly into the feeder house with an optional 18-in. (45.7-cm) top auger extending the full width of the draper.

RDF top auger RDF top auger
Benefits
  • With the crop tucked under the auger, the handoff to the center feed drum enables smooth and consistent feeding to the combine to ensure constant load.
  • Achieve smooth headfirst feeding when auger speeds are running slightly faster than the belt speed.
Additional details
  • This optional 18-in. (45.7-cm) hydraulically driven top auger has an easy speed adjustment at the right side of the platform.
  • It is recommended for operation in bushy or high-volume harvesting conditions such as canola.
  • Augers can be turned off for crops like lentils or wheat where they are not recommended.

Specifications


Compare the specifications of up to 4 models

Key Specs rd45f-hydraflex-draper
Current Model
Cutterbar length13.72 m
45 ft
Knife driveDouble-cut, dual-drive, shaft-driven cutterbar: 10.2 cm
4 in.
Knife speedX Series Combine: 520 cycles/min
S-Series Combine: 490 cycles/min
Pickup reel operating speeds6-70 rpm
Draper belts speed controlHydraulic from cab (side belts only)
Platform
Cutterbar
TypeStraight-line knife drive system
Cutterbar vertical flex: 190 mm
7.5 in.
Length13.72 m
45 ft
Knife driveDouble-cut, dual-drive, shaft-driven cutterbar: 10.2 cm
4 in.
Knife speedX Series Combine: 520 cycles/min
S-Series Combine: 490 cycles/min
Cutterbar tilt
Base skid shoe height3.8 cm
1.5 in.
Pickup reel
GeneralTwo-piece, poly tine pickup reel with 8-in. (20-cm) tube
Number of slatsSix bat poly
FingersNylon
Diameter106.7 cm
42 in.
Height controlHydraulic
Speed controlHydraulic
Reel lift72 cm
28.3 in.
Reel fore and aft35.9 cm
14.1 in.
Fore of the cutterbar40.6 cm
16 in.
Reel resumeBase
Reel reverseBase
Operating speeds6-70 rpm
Operating speeds (54-in. reel)
Slat reel
Number of slats
Diameter
Height control
Speed control
Operating speeds
Draper belts
WidthSide belts: 101.6 cm
40 in.
Center belts: 177.6 cm
70 in.
Belt depth101.2 cm
39.8 in.
Cleat height19.05 mm
0.75 in.
Operating speedSide belts (variable): 1-3.5 m/s
3.3-11.5 fps
Center belts: 211 m/min
692 fpm
Low-speed center belt (fixed): 4.2 m/s
13.8 fps
High-speed center belt (fixed): 5.1 m/s
16.7 fps
Speed controlHydraulic from cab (side belts only)
Center belt reverseBase
Feed drum
Diameter414 mm
16.3 in.
Feed drum fingersHeavy-duty and round with breakaway notch and retainer
Diameter: 16 mm
0.625 in.
Number of fingers21
Auger finger platformTriple chevron, retracting
Finger reach152 mm
6 in.
Drum/auger reverseBase
Operating speedLow speed: 200 rpm
High speed: 240 rpm
Center cleanout doorBase
Header height sensing
TypeElectrohydraulic
Header height sensing on the groundBase
Header height sensing off the groundOptional: four sensors
Top auger
TypeOptional: hydraulic drive
Fingered augers
Size45.7 cm
18 in.
Dimensions
Platform length14.6 m
47.9 ft
Overall operating depthWith dividers: 2.74 m
9 ft
Transport width, field position14.6 m
47.9 ft
Transport width on wheel, less dividers
Transport length, hitch extended
Weight