S770 COMBINE
Combine
- Combine Advisor™ package helps to set, optimize and automate main combine functions when conditions change
- Fully automated yield sensor calibration with ActiveYield™ supplies accurate data with no time spent calibrating
- Comfortable S700 cab is common with tractors and sprayers for ease of use
- Continued quality manufacturing of S-Series combines maximizes uptime and productivity
Apply For FinancingMaintenance Plans
Features
High-capacity harvesting in corn and beans
Harvesting in corn
Harvesting in beans
Designed for performance in coarse grain crops, the TriStream™ rotor and Dyna-Flo™ Plus cleaning shoe efficiently thresh and clean grain in tough harvesting conditions. The TriStream rotor helps maximize fuel efficiency with technology that reduces the force required to move material through the combine by as much as 20 percent. High capacity starts at the feeder house, where the S Series provides large areas of clearance for high volumes of crop to flow uninterrupted.
- TriStream rotor delivers performance – A slightly tapered front nose dramatically reduces the growling that often comes with thick crops and heavy rotor loads. Spiral vanes around the rotor guide the crop material through the feeding and threshing area, reducing hesitation and improving productivity. Meanwhile, rifling grooves on the elements allow the bullet-shaped rotors to move large volumes of crop material through the rotor more efficiently. Rifled elements grip crop material, providing a pulling action that helps even the crop flow, allowing the rotor to deliver better threshing performance.
- Dyna-Flo Plus delivers clean grain – Consider your capacity needs met. In fact, in shoe-limited conditions, you get 10 percent more capacity in corn than previous models, which equates to another 0.6 ha/hr (1.5 acre/hr). The key is uniform distribution and a unique two-stage pre-cleaning design. Four conveyor augers move material onto the shoe steadily and evenly, even on hillsides. A fixed front chaffer helps thin the crop mat; about 30 percent of the air goes to the front chaffer at high speed, allowing it to clean up to 40 percent of the free grain before it reaches the main chaffer. A huge rear chaffer and larger sieve (12 percent larger than previous models) are specially designed to handle the threshing and separating performance of the S Series.
Raise your capacity in tough small grains or rice
Harvesting in rice
Truly tough conditions demand more than simple solutions. Rather than slightly improve performance in rice, canola, wheat, barley, oats, or other tough small grains, John Deere S Series Combines set new capacity standards with four crucial components: Active Concave Isolation, a high-performance feeder house, heavy-duty interrupter grates with integrated interrupters, and the variable-stream rotor. When you’re looking at a storm on the radar and you don’t have time to spare, you can run full throttle and still put your toughest crop into the machine without any issues.
- Better material handling – The industry-exclusive variable-stream rotor features a longer, more tapered front cone design that excels in wet, green rice or small grains where the straw is especially tough. The variable-stream rotor with adjustable top cover transport vanes is recommended for rice producers and those facing tough threshing conditions. The vane angle can be adjusted to reduce the stress on straw material as it flows around the rotor, increasing the quality of the straw while using less fuel. Along with the tough material handling capabilities of the variable-stream rotor configuration, the straw quality and length can be improved due to the electrically adjustable top cover transport vanes.
- Dyna-Flo™ Plus cleaning shoe provides more cleaning capacity – In shoe-limited conditions, you’ll see a 14 percent capacity boost in wheat and canola compared to previous John Deere designs, raising your productivity and improving grain quality. Simply put, this is a cleaning system that does it all.
- Harvest through the toughest conditions – Active Concave Isolation has been improved by applying hydraulic pressure to better secure the concave, providing extra stability when harvesting really tough crops. This increases the machine capacity by 10 percent, so you can harvest outside the optimal harvest windrow or crop conditions when necessary.
- Better feeding in tough conditions – The S700 Combine feeder house design features an exclusive pivoting mid-frame design to provide the highest level of material handling and feeding capacity, especially in high-volume, tough crop conditions. The front feed drum provides you with 5.1 cm (2 in.) of additional movement for greater flexibility in challenging crop.
More convenience from the cab
Quick and easy adjustments in the cab
The more time you can spend harvesting and the less time spent making adjustments means more daily performance. The S Series Combine offers more convenience from the cab with platform tilt, precision residue, and easy crop changeover when it’s time to move fields. Whatever harvest throws at you, you can keep moving with the touch of a button.
- Platform tilt – A center-mounted hydraulic cylinder lets you adjust the platform tilt of the cutterbar from the convenience of the cab using the advanced multifunction lever. You get the optimum cutting angle and the lowest possible cutting height.
- Advanced PowerCast™ tailboard and straw chopper – This option for the premium residue system gives you additional residue management flexibility. With the premium system, you can chop straw and chaff and spread both by making adjustments within the cab. Auto Swap automatically adjusts for wind at headland turns. With the knife bank adjustment, you can change knife bank positions on-the-go from the cab to adjust residue sizing based on crop conditions or engine power consumption.
- Fast delivery, space-saving folds – S780 and S790 Combines boast a 14,100-L (400-bu) capacity to match high-volume crops and wider front-end equipment, while still emptying the tank as fast as 134 L/s (3.8 bu/sec). The folding unloading auger lets you store the combine in the barn using less space and makes the machine more maneuverable in tighter gateways. You can also control your grain tank covers and the loading auger from the CommandARM™ console in the cab with the push of a button.
Spend more time harvesting in tough conditions
The faster you can get to – and into – your fields, the more productive you are. John Deere S Series Combines make it easy. Tracks help you get into the field sooner and finish faster. The ProDrive™ system lets you smoothly shift between two speed ranges (field and transport) with the push of a button; you’ll no longer have to stop to shift when going up or down hills or when you’re exiting a field.
- Get your harvest on track – Your ability to get into your fields sooner is easier than ever. Reach a road transport speed of almost 40 km/h (25 mph) with the John Deere tracks. The suspended track system provides a smoother ride with better ground following. This makes for more comfortable harvesting days and lets you finish faster. Available with 76.2- or 91.4-cm (30- or 36-in.) wide belts, these tracks deliver better ride quality and ground following, improved flotation, and less compaction. In addition, there’s no daily maintenance.
Harvester with tracks
- ProDrive ground drive system – This lets you switch between two infinitely variable speed ranges with the push of a button. Using the CommandARM™ armrest console, you can set the first range for typical harvesting speeds and the second for transport. This reduces your combine’s engine rpms during transport while still maintaining a productive ground speed, improving fuel economy. An electrohydraulic differential lock with a four-pinion differential delivers greater traction in muddy conditions.
In-cab adjustments with CommandARM console
- Two-speed, four-wheel drive (4WD) is perfect for demanding conditions – This lets you switch between torque ranges. In slow-speed mode, the high-torque rear assist is ideal for tough conditions. Use high-speed mode for low-torque performance and faster ground speeds.
Spend the harvest day in comfort and in control
Comfortable S700 Combine cab
The S Series Combine Select cab is a great place to spend a long harvesting day. The intuitive CommandARM™ console, along with the 4600 CommandCenter™ Display, delivers easy-to-understand harvest run screens. The multi-function lever fits your hand perfectly to give you smooth hydrostatic speed control, unloading options, and more. An air-suspension swivel seat adjusts four ways with lumbar adjustments to give you just the right amount of support. For even more comfort, step into the Premium cab, equipped with a leather steering wheel, a leather, lumbar-supported operator seat that is heated and ventilated, plus a folding instructor seat. Even small cab comforts can make a big difference over long harvest days.
- Designed for efficiency – The Generation 4 CommandCenter display provides full-screen viewing of all your harvest run pages. It’s customizable with programmable shortcut keys that let you easily choose the pages you look at most frequently. You can also lock out functions to prevent less-experienced operators from accidentally making changes. Plus, the Extended Monitor works with the 4600 display to give you more real estate for viewing.
- Designed for productivity – The air suspension seat swivels 15 degrees to the right and 7 degrees to the left for better views of the grain tank and auger. Add grain tank mirrors for even better visibility of the fill level in the grain tank.
- Designed for comfort – An integrated refrigerator keeps refreshments cold all day, and foot pegs deliver improved comfort during long harvest days. These are small features that will make a big difference after 10 or more hours of daily harvesting.
Packed with ready-to-harvest technology
Harvesting technology in the cab
S Series Combines deliver more precision with integrated technologies to help you make upcoming business decisions with more accuracy. They learn on-the-go to improve your harvest, reduce losses, or leave cleaner grain. You’ll collect more accurate data, the automated technologies will improve harvesting results, and connecting all your machines will help you make more informed decisions. What’s even better, they do much of this automatically in the background without you having to worry about it, so you can focus on the harvest.
- Combine Advisor™ package – Combine Advisor automatically adjusts the combine’s harvest settings to put higher quality grain in the tank and reduce the chance of grain loss. Cameras on the clean grain and tailings elevator help you make informed decisions on the crop that is flowing up and into the grain tank.
- Automation 4.0 – The combine can unload 100 times or more every day with larger heads, so caution and safety are even more important. Machine Sync connects the grain cart to the combine, letting the combine operator adjust the speed and location of the cart and automating all tractor movement. The grain cart operator can see where all the combines are in the field, as well as which one is closest to full, prioritizing unloading and improving overall logistics. AutoPath™ system maps each planter row and maximizes harvest efficiency by creating your harvest AB lines, keeping the header full during each pass.
- 5-year subscription of JDLink™ Connect – JDLink automatically sends yield maps and other harvest data to the Operations Center for later analysis. From your office, JDLink gives you a look at all your machines – where they are, how they’re performing, and what action you can take to improve your harvest.
- Operations Center – Your combine generates more valuable data about your harvest than ever before. Operations Center makes it easier than ever to view, analyze, and compare different map layers and print out reports to make next year’s harvest even more profitable. Plus, you have access to more than 100 connected software tools, and you can easily share your harvest data with your trusted partners to help you make better decisions.
Specifications
Compare the specifications of up to 4 models
| Key Specs | s770-combine Current Model |
|---|---|
| Engine type | John Deere PowerTech™ PSS engine 9 L 548 cu in. |
| Rated power | 292 kW 391 hp |
| Fuel capacity | 950 L 250 gal. |
| Rotor length | 312 cm 123 in. |
| Rotor diameter | 76.2 cm 30 in. |
| Concave area | 1.1 m2 11.8 sq ft |
| Separating area | 1.54 m2 16.6 sq ft |
| Total cleaning area (louvered) | 5.1 m2 54.9 sq ft |
| Grain tank size | 10,600 L 300 bu |
| Unloading rate | 116.3 L/s 3.3 bu/sec |
| Engine | |
| Engine type | John Deere PowerTech PSS engine 9 L 548 cu in. |
| Emission level | Final Tier 4 / Tier 2 (Australia/New Zealand) |
| Rated speed | 2,200 rpm |
| Rated power | 292 kW 391 hp |
| Power boost @ rated speed | 25 kW 34 hp |
| Fuel capacity | 950 L 250 gal. |
| Feeding | |
| Drive type | Fixed or variable or multi-speed |
| Conveyor chain slat type | Cast iron |
| Width | 139.7 cm 55 in. |
| Length | 172.5 cm 67.9 in. |
| Feed Accelerator, Stone Trap (FAST) | Reverser Standard Standard |
| Threshing/ Separating | |
| Separator type | Rotary |
| Rotor length | 312 cm 123 in. |
| Rotor diameter | 76.2 cm 30 in. |
| Rotor speed range | 210-1,000 rpm |
| Concave area | 1.1 m2 11.8 sq ft |
| Separating area | 1.54 m2 16.6 sq ft |
| Discharge grate area | 0.36 m2 3.9 sq ft |
| Cleaning | |
| Front chaffer | 0.5 m2 5.4 sq ft |
| Chaffer | 2.5 m2 26.9 sq ft |
| Sieve area | 2.1 m2 22.6 sq ft |
| Total cleaning area (louvered) | 5.1 m2 54.9 sq ft |
| Cleaning fan speed | 620-1,350 rpm |
| Grain handling | |
| Grain tank size | 10,600 L 300 bu |
| Unloading auger length | 6.9, 7.9 or 8.7 m 22.5, 26 or 28.5 ft |
| Unloading rate | 116.3 L/s 3.3 bu/sec |
| Base weight - less head | |
| Total machine | 18,950 kg 41,778 lb |
| Manufacturing location | |
| Country | USA, East Moline, Illinois |
Accessories and Attachments
Bracket
10" Tablet Holder Kit - BXE10901
12 Tablet Holder Kit (Ipad Pro) - BXE10864
Camera Observation System
The camera-ready feature is optional on all S700 Combines and provides factory-installed observation camera harnesses and brackets in the grain tank, on the unloading auger, and at the rear of the combine. John Deere value:Provides increased visibility options when unloading grain and maneuvering the combine in and out of the fieldFour integrated camera views on the 4600 CommandCenter™ Display for more convenience Functionality:Quickly install compatible cameras, orderable from Service PartsHarness and brackets are provided factory installed, cameras have to be ordered separately via PartsRearview camera locationUnloading auger camera locationUnloading auger camera locationGrain tank camera locationCamera trigger menuCamera triggers with time menu for:Reverse with separator on video triggerReverse with separator off video triggerSeparator video trigger3/4 grain tank video trigger4/4 grain tank video triggerTrigger menu for cameras NOTE: 4600 CommandCenter is capable of viewing up to four cameras simultaneously. NOTE: Cameras are not included with factory-installed option. Please order cameras from Service Parts.
Voyager Camera - SWCVMS155B
Voyager One Camera Kit - SWVCMS155JD1
Voyager Three Camera Kit - SWVCMS155JD3
Chaffer And Sieve
3 mm Fixed Round Hole Sieve - AXE68434
The Dyna-Flo Plus cleaning shoe is the heart of the S700 Combine cleaning system. The system is made up of a unique design consisting of aluminum and high-strength steel that reduces overall weight while maintaining overall strength. The Dyna-Flo Plus cleaning shoe also features an enhanced drive system that requires only one flywheel for optimal shoe performance and maximizes uptime.Feature benefit:Increased size of the sieve area by 12 percent for up to an additional 0.6 ha (1.5 acres) per hour of productivity.Tailings volume reduction of up to 28 percent in coarse grains and up to 14 percent in small grains.Weight reduction of 180 kg (396 lb) for smoother operation and reduced combine ground compaction.Dyna-Flo Plus cleaning shoeEnhanced drive systemFunctionality:The Dyna-Flo Plus cleaning system begins with conveyor augers located beneath the concave area, where the volume of threshed material is highest, to evenly move material onto the cleaning shoe (1). The deep auger troughs provide uniform distribution of material to the cleaning shoe with less bunching, even on sloping terrain and when harvesting up and down hills.Dyna-Flo Plus cleaning shoeOnce grain is on the cleaning shoe, the raised-center front chaffer cleans up to 40 percent of free grain before it reaches the main chaffer (3). High-velocity air from the cleaning fan elevates any light material traveling over the end of the front chaffer, resulting in more aggressive separation of chaff and increased cleaning performance (2). The main chaffer provides grain separation from chaff as the grain passes through the main chaffer to the sieve (4).The sieve provides proper sizing of grain from material other than grain (5). Any grain that passes through the sieve is elevated to the grain tank while some grain or material other than grain flows to the tailings return system for reprocessing. On S760, and S770 Combines, the tailings material is directed back into the threshing section of the separator for additional threshing. The tailings material on the S780 and S790 Combines are directed to the active tailings return system for additional threshing, and then directed back on the return pan and then onto the main chaffer for additional cleaning (6).
Parts included for side hill packageThe side hill performance package can improve combine performance on slopes up to 8 degrees (14 percent) by substantially reducing cleaning shoe grain loss to acceptable levels. Feature benefit:Reduces grain loss out of the rear of the combine on side hill slopesIncreases combine productivity by not having to slow down on side hill slopes Functionality: The side hill kit installed in the cleaning shoe of S700 Combines allows grain to be evenly distributed across the entire width of the shoe when harvesting in slopes. As grain moves to the rear of the combine, the dividers keep grain contained into four individual bays which prevents overloading one side of the cleaning shoe. Additionally, the rubber agitator paddles in each individual bay work with the oscillating motion of the cleaning shoe to move grain toward the center of each bay for increased utilization of the entire cleaning shoe width for increased performance and productivity.
Deep Tooth Chaffer - AXE60613
Deep Tooth Sieve - For TouchSet Remote Combine Adjustment: S760-S790 - AXE68433
General Purpose Sieve - AXE60449
Concaves And Threshing
Round-bar concaves are standard equipment on corn combines and are recommended for use in corn and soybeans. Additionally, they are recommended for use in specialty crops such as edible beans and food corn. Feature benefit:Provide maximum grain quality and productivity when harvesting corn or soybeansAllow versatility to harvest cereal grain crops when paired with the round-bar concave insertsRound-bar multi-crop concaveSee concave recommendations to choose the concaves that are best for a grower's operation. The front concave section is heat treated. All three sections are available to be heat treated as an option or in the extended-wear separator package.
Additional threshing tine base weldments for installation into the DensePack locations of a variable-stream rotor can only be used to improve material handling in some tougher conditions such as rice and grass seed harvest. This may decrease machine performance if used in dry, brittle-crop conditions. Feature benefit:Rice machines ordered from the factory already come with these tines installed for increased productivity and capacityIncrease in machine performance in tough-threshing and damp cropsVariable-stream rotor equipped with DensePackGrain wear platesRice wear plates Wear plate kits (grain versus rice) must be ordered separately through Service Parts.
Rear of rotor with discharge paddlesRotor discharge flights are available for STS combines when operating in specialty crops. The discharge flights are recommended for use in crops such as sunflowers and edible beans when operating in conditions that require rotor threshing speeds below 300 rpm. The discharge flights are designed to provide an aggressive push to the slow-moving crop material as it moves from the rotor housing into the discharge beater. The additional kick provided by the paddle design of the flighting significantly improves material flow and reduces possible plugging at the rear of the rotor at extremely low threshing speeds. When operating in other crops where rotor speeds higher than 300 rpm are required (for example, soybeans, wheat, rice, etc.), it is recommended the discharge flights BE REMOVED to ensure adequate and even material flow through the rotor, as well as to provide better residue spread. IMPORTANT: Discharge flight paddles are NOT recommended for use in heavy, damp wheat or rice crops. The discharge flight is for use on any 9650 STS, 9750 STS, 9660 STS, 9760 STS, 9860 STS, 9670 STS, 9770 STS, and 9870 STS Combines and does not require the combine to be fitted with any particular configuration of rotor discharge housings. NOTE: Two rotor discharge flight paddles for 9560 STS, 9570 STS, and S550 STS Combines, AH219961 and AH219962, can be ordered through Service Parts.
Round-bar concaves are standard equipment on corn combines and are recommended for use in corn and soybeans. Additionally, they are recommended for use in specialty crops such as edible beans and food corn. Feature benefit:Provide maximum grain quality and productivity when harvesting corn or soybeansAllow versatility to harvest cereal grain crops when paired with the round-bar concave insertsRound-bar multi-crop concaveSee concave recommendations to choose the concaves that are best for a grower's operation. The front concave section is heat treated. All three sections are available to be heat treated as an option or in the extended-wear separator package.
Small-wire concaves are standard equipment on small-grain combines and are recommended for use in wheat, barley, and other cereal crops. The small-wire concaves are recommended for use in specialty crops such as grass seed. Feature benefits:Provide maximum grain quality and productivity when harvesting small grainsAllow versatility to harvest specialty crops such as grass seed without having to switch out concavesSmall-wire concave for small grain See concave recommendations to choose the concaves that are best for grower's operation. The small-wire concaves are also available as an option with boronized treatment for extended-wear life. This process penetrates the surface of the concave with a layer of hard, wear-resistant material, extending the life of the concave up to twice as long, and is available in the extended-wear separator package. IMPORTANT: Not recommended for use in corn.
Large-wire concaves are standard on S700 Rice Combines and available as an option on corn and small-grain combines. They are recommended for rice, sorghum, soybeans, and corn. Feature benefit:Best separating performance in rice to maximize productivityVersatility to perform well in soybean harvest, eliminating the need to change out concaves or purchase additional set of concavesLarge-wire concaveLarge-wire concaves are standard on S700 Rice Combines and available as an option on corn and small-grain combines. They are recommended for rice, sorghum, soybeans, and corn. See concave recommendations to choose the concaves that are best for grower's operation. As an option, all three sections can be boronized for extended-wear life. This process penetrates the surface of the concave with a layer of hard, wear-resistant material, extending life up to twice as long.
Large-wire concaves are standard on S700 Rice Combines and available as an option on corn and small-grain combines. They are recommended for rice, sorghum, soybeans, and corn. Feature benefit:Best separating performance in rice to maximize productivityVersatility to perform well in soybean harvest, eliminating the need to change out concaves or purchase additional set of concavesLarge-wire concaveLarge-wire concaves are standard on S700 Rice Combines and available as an option on corn and small-grain combines. They are recommended for rice, sorghum, soybeans, and corn. See concave recommendations to choose the concaves that are best for grower's operation. As an option, all three sections can be boronized for extended-wear life. This process penetrates the surface of the concave with a layer of hard, wear-resistant material, extending life up to twice as long.
This attachment is used for rice configured machines only. Rice performance enhancement package contains spike caps, and long threshing tines. When it is used in certain crop conditions, it may enhance the performance of the combine. Attachment includes instructions on how and when to use the components.Spike capsSeparator grate interruptersLong threshing tines
Concave cover plates for round-bar concaves onlyConcave sectionalized cover plates for round-bar concaves help to increase performance in the threshing area in tough conditions and can improve material distribution from the concaves to the cleaning system.
Concave cover plates for round-bar concaves onlyConcave sectionalized cover plates for round-bar concaves help to increase performance in the threshing area in tough conditions and can improve material distribution from the concaves to the cleaning system.
Small-wire concaves are standard equipment on small-grain combines and are recommended for use in wheat, barley, and other cereal crops. The small-wire concaves are recommended for use in specialty crops such as grass seed. Feature benefits:Provide maximum grain quality and productivity when harvesting small grainsAllow versatility to harvest specialty crops such as grass seed without having to switch out concavesSmall-wire concave for small grain See concave recommendations to choose the concaves that are best for grower's operation. The small-wire concaves are also available as an option with boronized treatment for extended-wear life. This process penetrates the surface of the concave with a layer of hard, wear-resistant material, extending the life of the concave up to twice as long, and is available in the extended-wear separator package. IMPORTANT: Not recommended for use in corn.
Corn
Engine
110V Pump Kit - SW110VDEFSS
12V Pump Kit - SW12VDEFSS
65 gal. Portable Dispensing Unit with lockable, hinged lid - SWDEFPDU65M
Air Compressor Conversion Kit - BXE10698
Air Compressor Conversion Kit - BXE10699
The rotary screen brush kit adds a series of brushes to the rotary screen. The brushes prevent debris from building up on the screen, allowing full air flow to the engine for cooling.
Engine
275 gal. Tote of John Deere Diesel Exhaust Fluid - SWDEF275
330 gal. Tote of John Deere Diesel Exhaust Fluid - SWDEF330
55 gal. drum of John Deere Diesel Exhaust Fluid - SWDEF055
Fast (Feed Accelerator And Stone Trap)
Contoured serrated wear stripsRegular straight serrated wear stripsThe serrated feed accelerator wings have a smooth contoured back to provide fast yet gentle crop handling while also featuring serrated edges for positive crop movement in viney crops such as edible beans. The updated feed accelerator wings are recommended in place of the optional smooth accelerator wear strips attachment because they help to provide excellent grain quality without compromising feeding performance in edible beans.NOTE: The standard straight serrated wear strips are still the recommended choice to use on the feed accelerator when harvesting in damp or green-stemmed-type crops.
Stone trap and stone trap handleThe stone trap protects the combine's interior area by effectively catching stones deflected by the feed accelerator into the stone dump area before they enter the TriStream™ feed section.Remote lever with an over-center latch makes cleanout fast and easy.Trap requires no adjustment and provides worry-free harvesting when cutting close to the ground.Adds no additional length to the feederhouse. Excellent line-of-sight visibility of the platform cutterbar is maintained.No compromise in feeding material smoothly from the platform to the feederhouse conveyor chain.No increase in front axle tire loading since feederhouse length is not extended. Base Equipment On: S-Series Combines Field-installation informationAn expanded stone trap door with a two-piece front feed floor is available as a field-installed bundle. This bundle replaces the standard one-piece feed floor. When harvesting crops such as corn, food corn, popcorn, and small grains, the front-piece floor section remains bolted in place. This allows 9 in. of opening across the width of the machine. In rocky conditions such as beans and edible beans, the front floor section is removed to provide 11.5 in. of open area to the larger stone trap, allowing improved rock protection (22 percent increase in stone trap area). Please refer to the chart below for retro-fit information
Two-speed feed accelerator handle The slow-speed drive reduces the standard two-speed feed accelerator from 450 rpm/800 rpm to 320 rpm/770 rpm. These lower speeds allow the feed accelerator to provide more gentle grain handling in delicate specialty crops such as edible beans, food corn, or popcorn. Having the slow-speed feed accelerator drive available as a factory-installed option allows those who plan on using this drive for harvesting all their crops to save the cost of discarding the standard feed accelerator drive parts in the field.
Smooth-wear strips on feed acceleratorThe smooth-wear strips provide optimum grain quality in speciality crops such as popcorn and food corn. The bundle includes set of 30 wear strips to replace standard-equipment serrated wear strips.
Tine FAST feed acceleratorCombed floorThe enhanced rice performance attachment is recommended for improved harvesting capacity when rice conditions may be limited due to slugs and heavy loads from straw intake while harvesting. This attachment provides smoother feeding and better material handling, along with increased rice harvesting capacity. The attachment includes the tine feed accelerator and stone trap (FAST) system, combed floor, threshing tines, discharge paddles, and directions on how to move the existing feed accelerator to the discharge location. Threshing tinesDischarge beater
Tine Feed Accelerator - BH84416
Grain Handling
Grain tank level sensorThe fast, easy way to let the operator know the combine’s grain tank is full when harvesting on side hills.Feature benefits:Beacons activatedImproved accuracy when harvesting in hilly terrain Prevents overfilling the grain tank Functionality: An additional grain tank level indicator is available to help detect a full grain tank. The beacon lights are also activated when the combine is in road transport mode.
Door, Regular Duty, Perforated - S660/S760, S670/S770, S680/S780 - BXE10094
Perforated Clean Grain Elevator Boot, Door - BH81519
Perforated and Clean Grain Doors - BH80611
When harvesting in wet or dirty conditions, the steel-paddle tailings elevator can be installed to remove the build-up of dirt and debris.
Greenstar Brackets
Harvest Information Technology
ActiveYield delivers automatic yield calibrations to the operator without spending time manually performing yield calibrations.Feature benefit:Simplified yield calibrations for improved uptime in the fieldSimplified data collection for use during and after harvestFunctionality:ActiveYield eliminates time-consuming manual yield calibrations and replaces them with automated sensors that calibrate the machine by measuring the grain as the tank fills. This enables decisions to be made in real time without leaving the cab.ActiveYield sensors in grain tankWhen the ActiveYield option is enabled and the Terrain Compensation Module (TCM) in the StarFire™ 3000 or StarFire 6000 Receiver has been calibrated, ActiveYield is ready to go to work. As grain is harvested and enters the tank, the three sensors within the grain tank collectively measure the grain as it piles over the cross auger covers. If all conditions are acceptable (header and separator on, grain is flowing, and machine level is within 4 degrees) load collection occurs from 900 through 3000 kg (2000 through 6600 lb).Any pitch and roll of more than 4 degrees from center during load collection will cause the system to reject that load due to the grain pile shifting in the tank. A new calibration load starts once grain is below the sensors on the cross auger covers.Stored calibration loads are replaced by new ones as the system continues to collect data. The system may be disabled at any time by accessing the moisture setup page and unchecking the ActiveYield box if manual yield calibration is desired.ActiveYield calibration locationActiveYield InformationActiveYield is available for model year 2016 through model year 2019 S760, S770, S780, and S790 Combines and requires the 4600 CommandCenter™ Display, GreenStar™ 3 2630 Display, or GreenStar 3 CommandCenter. Additionally, a StarFire 3000 or 6000 Receiver must be installed on the combine with the TCM calibrated for ActiveYield to detect machine pitch correctly. Manual yield calibration is not required as each crop has a built-in default value.Harvest Doc™ system yield data collected by an ActiveYield system is only compatible with the John Deere Operations Center. John Deere does not guarantee compatibility of ActiveYield collected documentation with John Deere APEX™ software or third-party software systems.
Ladder Extension
This bolt-on access platform attachment is required for S700-Series Combines that are ordered less wheels and tires and later equipped with single front drive tires. Refer to the tire compatibility charts in the Agricultural Sales Manual for specific drive tire sizes and compatibility information for the 230-mm (9-in) bolt-on access platform. This attachment includes all the parts to install this ladder extension on S700-Series Combines.
This bolt-on access platform attachment is required for S-Series Combines that are ordered less wheels and tires and later equipped with single front drive tires. Refer to the tire compatibility charts in the Agricultural Sales Manual for specific drive tire sizes and compatibility information for the 330 mm bolt-on access platform. This attachment includes all the parts for this specific ladder extension installation.
This bolt-on access platform attachment is required for S-Series Combines that are ordered less wheels and tires and later equipped with either dual front or single drive tires with axle spacers. Refer to the tire compatibility charts in the Agricultural Sales Manual for specific dual and single drive tire sizes and compatibility information for the dual tire platform extension.
Long-length ladder extension for S-Series Combines ordered less wheels and tiresThis 1554-mm (61.2-in.) length ladder is required for S-Series Combines that are ordered less wheels and tires and later equipped with front drive tires for S-Series Combines that have a static loaded radious (SLR) of 910 mm (36 in.). Refer to the tire compatibility charts in the Agricultural Sales Manual for specific drive tire sizes and compatibility information for the long length 1554-mm (61.2-in.) ladder.
Medium Length Ladder - BXE10421
Short Length Ladder - BXE10422
Machine Optimization Technology
Active Terrain Adjustment is a system that enhances grain quality and reduces grain loss when harvesting on ascending or descending hills. The feature automatically adjusts the combine’s sieve and chaffer openings and carefully controls the cleaning fan speed, stabilizing tailings levels and ensuring a clean grain tank sample. Feature benefit:Achieves same loss level as on level land conditions (on hills up to 10 degrees)Tailings reductions by up to 35 percent on 8-12-degree inclinesAutomatic settings adjustments on hillsActive Terrain Adjustment slopeFunctionality: Order Active Terrain Adjustment as a factory-installed option or as an attachment for field installation on model year 2016 machines and newer (PIN 785000 -). The feature can be used in both coarse and small grains in all terrain, but will excel especially on hills.Active Terrain Adjustment pitch sensorActive Terrain Adjustment cleaning fan actuatorWhen the machine starts an uphill climb, Active Terrain Adjustment will slow the cleaning fan down and open the chaffer and sieve elements. As the machine descends a hill, the cleaning fan speed will increase and the chaffer and sieve elements will close to decrease grain loss and prevent shoe loading.
ICA2 Retrofit Bundle for S760 and S770 Combines - BXE11034
Mirrors
Miscellaneous
105-mm (4-in.) Axle Spacer - BH92136
12 In. (300 mm) Axle Spacer - HXE71480
16 In. (400 mm) Axle Spacer - HXE71479
165-mm (6.5-in.) Axle Spacer - BH92139
454-mm (18-in.) axle spacer - BH92142
ActiveYield delivers automatic yield calibrations to the operator without spending time manually performing yield calibrations.Feature benefit:Simplified yield calibrations for improved uptime in the fieldSimplified data collection for use during and after harvestFunctionality:ActiveYield eliminates time-consuming manual yield calibrations and replaces them with automated sensors that calibrate the machine by measuring the grain as the tank fills. This enables decisions to be made in real time without leaving the cab.ActiveYield sensors in grain tankWhen the ActiveYield option is enabled and the Terrain Compensation Module (TCM) in the StarFire™ 3000 or StarFire 6000 Receiver has been calibrated, ActiveYield is ready to go to work. As grain is harvested and enters the tank, the three sensors within the grain tank collectively measure the grain as it piles over the cross auger covers. If all conditions are acceptable (header and separator on, grain is flowing, and machine level is within 4 degrees) load collection occurs from 900 through 3000 kg (2000 through 6600 lb).Any pitch and roll of more than 4 degrees from center during load collection will cause the system to reject that load due to the grain pile shifting in the tank. A new calibration load starts once grain is below the sensors on the cross auger covers.Stored calibration loads are replaced by new ones as the system continues to collect data. The system may be disabled at any time by accessing the moisture setup page and unchecking the ActiveYield box if manual yield calibration is desired.ActiveYield calibration locationActiveYield InformationActiveYield is available for model year 2016 through model year 2019 S760, S770, S780, and S790 Combines and requires the 4600 CommandCenter™ Display, GreenStar™ 3 2630 Display, or GreenStar 3 CommandCenter. Additionally, a StarFire 3000 or 6000 Receiver must be installed on the combine with the TCM calibrated for ActiveYield to detect machine pitch correctly. Manual yield calibration is not required as each crop has a built-in default value.Harvest Doc™ system yield data collected by an ActiveYield system is only compatible with the John Deere Operations Center. John Deere does not guarantee compatibility of ActiveYield collected documentation with John Deere APEX™ software or third-party software systems.
Chopper Drive Shielding - BXE10357
Deflector for PowerCast tailboard This is the seal that is needed convert to the PowerCast tailboard.
Distribution bundle/deflector for premium residueIs recommended to use when you have uneven residue distribution as a result of uneven material coming from the discharge beater. This bundle will help to improve that distribution as it’s moved into the residue system.
Driveshaft bundle, S-Series w/ No Axle Spacer - BH84580
Dyna-Flo Plus Chaffer - AXE48125
Enhanced single-point latching systemJohn Deere’s single-point header latching system provides combine operators a fast and easy method for connecting all front-end equipment. One easy motion of the lever connects the electrical and hydraulic circuits along with header retaining pins.No wrenches are required to complete the header-combine connectionReduces the time required to change over headers, so there is more time available for harvestingMore convenient to remove headers for transport or storageThe enhanced single-point latching system, starting in model year 2016, will include a valve assembly mounted to all platform and corn head back sheets. These assemblies will include an orifice valve unique to the header type as well as a pressure override valve. Together, these ensure optimum performance and reliability of header hydraulic functions. Compatibility for prior headers or combines to model year 2016 equipment is provided by attachments specific to the header and combine being used. Refer to the chart below for compatibility information. Six different attachments cover the compatibility between new and used combines and front-end equipment. The attachments are BXE10667, BXE10666, BXE10668, BXE10670, BXE10697, and BXE10669.
Enhanced single-point latching systemJohn Deere’s single-point header latching system provides combine operators a fast and easy method for connecting all front-end equipment. One easy motion of the lever connects the electrical and hydraulic circuits along with header retaining pins.No wrenches are required to complete the header-combine connectionReduces the time required to change over headers, so there is more time available for harvestingMore convenient to remove headers for transport or storageThe enhanced single-point latching system, starting in model year 2016, will include a valve assembly mounted to all platform and corn head back sheets. These assemblies will include an orifice valve unique to the header type as well as a pressure override valve. Together, these ensure optimum performance and reliability of header hydraulic functions. Compatibility for prior headers or combines to model year 2016 equipment is provided by attachments specific to the header and combine being used. Refer to the chart below for compatibility information. Six different attachments cover the compatibility between new and used combines and front-end equipment. The attachments are BXE10667, BXE10666, BXE10668, BXE10670, BXE10697, and BXE10669.
Extra-Fine-Cut Chopper with American Power Conversion (APC) Outlet - BXE10170
S-Series standard straw spreaderThe twin-disc straw spreader system uses two large impellers to ensure uniform distribution of material from the separator and cleaning system. The spreader is recommended for use when tillage practices do not dictate fine sizing of crop residue.
Perforated and Clean Grain Doors - BH90075
When harvesting in wet or dirty conditions, the steel-paddle tailings elevator can be installed to remove the build-up of dirt and debris.
The large tool cabinet is available on model year 2019 and newer combines models.Integrated design can fold away on the left-hand side of the combine with a hinge at ground level, so the toolbox does not have to be completely removed from the machine.117-L (4.1-cu ft) of storage on two decksCompartment can be locked with a keyTwo tool cabinet decksTool cabinet storage space
Operator's Station
Retrofit Kit for Foot Pegs - KXE10454
Ash tray and cigarette lighter attachment for S-Series cabs
Radio
Rear Axle With 2-Speed, 4-Wheel Drive
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
S700 rear-wheel assist motorContinue harvesting, even in muddy conditionsFeature benefit:Allows harvest to continue in muddy field conditionsProvides increased maneuverability and steering when ground conditions are wet or slickIncreases ground drive torque that may be needed when harvesting on slopesTwo-speed feature provides versatility to maximize harvest productivity when maximum ground drive torque or faster ground speed is needed. Functionality:Specifications of the 2294-cc (140-cu in.) 4WD system include:In the slow-speed mode, the system provides a maximum of 2294-cc (170-cu in.) displacement per motor for maximum (high-torque) rear-wheel assist.In the high-speed mode, the system provides 1147 cc (70 cu in.) of displacement for (low-torque) rear-wheel assist and faster ground speed capability.On all ProDrive™ transmission machines, low-speed 4WD engagement is limited to 10 km/h (6.2 mph) and high-speed 4WD engagement is limited to 15.9 km/h (9.9 mph) with maximum speed up to 20 km/h (12.4 mph).
S700 rear-wheel assist motorContinue harvesting, even in muddy conditionsFeature benefit:Allows harvest to continue in muddy field conditionsProvides increased maneuverability and steering when ground conditions are wet or slickIncreases ground drive torque that may be needed when harvesting on slopesTwo-speed feature provides versatility to maximize harvest productivity when maximum ground drive torque or faster ground speed is needed. Functionality:Specifications of the 2294-cc (140-cu in.) 4WD system include:In the slow-speed mode, the system provides a maximum of 2294-cc (170-cu in.) displacement per motor for maximum (high-torque) rear-wheel assist.In the high-speed mode, the system provides 1147 cc (70 cu in.) of displacement for (low-torque) rear-wheel assist and faster ground speed capability.On all ProDrive™ transmission machines, low-speed 4WD engagement is limited to 10 km/h (6.2 mph) and high-speed 4WD engagement is limited to 15.9 km/h (9.9 mph) with maximum speed up to 20 km/h (12.4 mph).
Axle spacers enable specific tire spacing for S-Series Combines. Reference the attached Ag Sales Manual S-Series tire spacing chart for specific tire, tire spacing, and recommended axle spacer information. The axle spacer attachments include axle spacers, attaching hardware, truss rods, couplers, and shaft extensions. Ladder extensions are typically required and ordered separately to provide the necessary clearance between the tires and ladder. Please reference the following documents for more detailed information.S-Series tire compatibility and spacing chartAxle spacer chart
Enhanced single-point latching systemJohn Deere’s single-point header latching system provides combine operators a fast and easy method for connecting all front-end equipment. One easy motion of the lever connects the electrical and hydraulic circuits along with header retaining pins.No wrenches are required to complete the header-combine connectionReduces the time required to change over headers, so there is more time available for harvestingMore convenient to remove headers for transport or storageThe enhanced single-point latching system, starting in model year 2016, will include a valve assembly mounted to all platform and corn head back sheets. These assemblies will include an orifice valve unique to the header type as well as a pressure override valve. Together, these ensure optimum performance and reliability of header hydraulic functions. Compatibility for prior headers or combines to model year 2016 equipment is provided by attachments specific to the header and combine being used. Refer to the chart below for compatibility information. Six different attachments cover the compatibility between new and used combines and front-end equipment. The attachments are BXE10667, BXE10666, BXE10668, BXE10670, BXE10697, and BXE10669.
Parts Assembly - Box of Final Drive Axle Extensions - BH81747
Residue Disposal
Paddles for APC corn kitPaddles for APC corn kitThe Advanced PowerCast tailboard corn kit is recommended for combines that are equipped with the Advanced PowerCast tailboard during the corn harvest. The tailboard kit prevents damage to the straw paddled by large corn cobs and other foreign material. This attachment will improve distribution and wear characteristics of the Advanced PowerCast system when used in corn.
Adjustable Finger Rakes - KXE10296
Overshot beater corn kit coverOvershot beater corn kit coverThe overshot beater corn kit attachment is ideal for combines that are equipped with the premium residue tailboard during corn harvest. This attachment will protect the cleaning shoe from damage from cobs that can be thrown by the overshot beater.
Deflector Windrow Convergence Kit - AH210317
Fine-cut chopper with vane tailboard outletThis attachment is needed when converting from a less-residue option or straw spreaders to a fine-cut chopper. The S-Series straw chopper provides sizing and spreading of residue material across the entire width of the platform cutting width.
Fine Cut Chopper with Standard VTB Outlet - BXE10660
S-Series standard straw spreaderThe twin-disc straw spreader system uses two large impellers to ensure uniform distribution of material from the separator and cleaning system. The spreader is recommended for use when tillage practices do not dictate fine sizing of crop residue.
Hydraulics and electrics for Advanced PowerCastThis attachment is for the hydraulic and electrics required for the Advanced PowerCast conversion.
Hydraulic Plus Electric for Advanced PowerCast Fine-Cut and Extra-Fine-Cut (FC and XFC) - BXE10817
Hydraulics and electrics for spreadersThe twin-disc straw spreader system uses two large impellers to ensure uniform distribution of material from the separator and cleaning system. The spreader is recommended for use when tillage practices do not dictate fine sizing of crop residue. Straw spreader options: 1. Standard straw spreaderThis spreader is not recommended for use with greater than 9.14-m (30-ft) platforms 2. Widespread straw spreader (not available on the S650)This spreader is recommended for use with 9.14-m (30-ft) to 12.2-m (40-ft) platformsOn the S660-S690 speeds of the spreader can be independently controlledThis spreader is not recommended for use in rice applications
Hydraulics and electrics for spreadersThe twin-disc straw spreader system uses two large impellers to ensure uniform distribution of material from the separator and cleaning system. The spreader is recommended for use when tillage practices do not dictate fine sizing of crop residue. Straw spreader options: 1. Standard straw spreaderThis spreader is not recommended for use with greater than 9.14-m (30-ft) platforms 2. Widespread straw spreader (not available on the S650)This spreader is recommended for use with 9.14-m (30-ft) to 12.2-m (40-ft) platformsOn the S660-S690 speeds of the spreader can be independently controlledThis spreader is not recommended for use in rice applications
Hydraulics and electrics for PowerCastThis attachment is the hydraulic and electrics required for the PowerCast conversion.
Knife Kit - KXE10363
PowerCast tailboardS680 with PowerCast tailboardTo better manage residue distribution with wider platforms, the PowerCast tailboard spreads residue 9.1 m (30 ft) and wider. This feature spreads residue evenly which helps set the stage for even crop emergence once planted, especially in no-till farming practices. The PowerCast tailboard is a hydraulically powered tailboard assembly that mounts to the rear of the chopper. Two hydraulically driven, counter-rotating discs with paddles are mounted in the tailboard. Crop is discharged from the chopper to the spinning discs, where the velocity of the residue is increased so it can be distributed across the platform cut width, as desired. The distribution discs are driven by the same pump, and the speed is controlled by a button on the CommandTouch™ armrest.
Premium Chopper Vane Kit for 7.6m (25 Ft.) Spread Width - AH219763
Standard deflectorsThis attachment is for producers moving from straw spreaders/less residue to a deluxe residue system equipped with a vane tailboard.
Manual vane tailboardManual vane tailboard mountedThe manually adjustable vane tailboard design provides a residue spread pattern for platform cut widths up to and including 9.14 m (30 ft). The manually adjustable vane tailboard allows simple vane angle adjustments from the ground. Manually adjust the vane position, as required, to meet the desired spread width.