9RT 570
Tractor
- Engine HP1: 627 Max/ 570 hp Rated
- Fully integrated precision ag technology
- e18™ PowerShift Transmission
- Choice of three different cab and visibility packages
1Engine power PS (hp ISO) at max engine power speed (ECE-R120). John Deere Standard RES10080, SAE Standards J1995.
Apply For Financing
Features
JD14 (13.6L/827-cu in.) engine: real world usability, not just power on paper
JD14 engine
The muscle to handle heavy draft disks and rippers, power-hungry air seeders and planters, and large transport loads like grain carts and slurry wagons. The durable design and heavy-duty components you can depend on when you need to get in and get out. All in a Final Tier 4 (FT4) and Stage V compliant package. You get real-world power with the purpose-built JD14 (13.6L/827-cu in.) engines from John Deere Power Systems, standard in the 291 to 471 engine kW (390 to 640 engine hp) 9 Series Tractors.
We developed our newest power plant from a clean sheet of paper, starting with stronger castings, beefier bearings, and more robust internal components, all designed to meet the high demands of field operations. We replaced the fuel injectors with a high-pressure common rail (HPCR) fuel system and eliminated the diesel particulate filter (DPF) to boost to fuel efficiency and lower operation and maintenance costs. Integrated coolant and oil passages, along with a new belt-driven water pump, eliminate potential leak points and allow for a less-crowded engine compartment, improving serviceability and reducing debris accumulation.
In redesigning the engine, we also gave it:
- Hydraulic valve lash adjusters to maintain valve-lash settings during engine operation, reduce valve train noise and wear, and allow for greater fuel efficiency.
- A hydraulic fan drive for improved cooling capacity with no required maintenance.
- A new integrated wiring harness design featuring a modular layout for reduced vibration, greater reliability, and easier service and diagnostics.
- A rear gear train that integrates fully into the cast-iron block, reducing tiresome engine noise and improving the durability of the crankshaft damper.
- Combination sensors where possible, meaning fewer sensors, connectors, and wires.
- A powerful engine brake that allows operators to use the engine to control tractor and implement speeds while transporting or traveling downhill, reducing wear on the drivetrain brake components.
It all adds up to:
- 14 percent more power and 11 percent more torque
- 3 percent lower fuel consumption
- 10 percent lighter
- 13 percent reduction in mean repair time and an estimated $8,308 savings in service costs over the life of the engine
13.5L (824-cu in.) engine compared to JD14 (13.6L/827-cu in.) engine
| Feature | 13.5L (824-cu in.) engine | JD14 (13.6L/827-cu in.) engine |
| Fuel delivery | Electronic unit injectors (EUI) | HPCR |
| Aftertreatment | Two canisters | One canister |
| Valve lash adjustment | Manual | Automatic |
| Engine brake | Not available | Available above 402.7 kW (540 hp) |
| Wire harness | Single harness | Three short harnesses |
| Water pump | Gear driven | Belt driven |
| Gear train | Front mounted | Rear mounted |
| Fan drive | Vari-Cool™ system | Hydraulically driven |
NOTE: The PowerTech™ 13.6L (827-cu in.) engine has been renamed the JD14.
9 Series Visibility packages let you run with confidence, dawn until dusk
Ultimate Visibility package at night
Visibility is more than just lighting. It’s mirrors where you need them, shades for the blinding late-fall and early-spring sun, wipers to help keep all the glass clear, and integrated camera capability. The new 9 Series Tractors let you choose the visibility package that best suits your needs – Select, Premium, or Ultimate with 360-degree light-emitting diode (LED) lighting –so you and your operators can run with all-conditions confidence.
| Select | Premium | Ultimate | |
| Lighting | 18 halogen worklights | 18 LED worklights | 24 LED worklights and eight LED convenience lights* |
| Mirrors | Mechanical | Electric and heated | Electric, heated, and telescoping |
| Sunshades | Front | Front, right-hand side, and rear | Front, right-hand side, and rear |
| Wipers | Front and rear | Front, right-hand side, and rear | Front, right-hand side, and rear |
| Cameras | Camera ready | Camera ready | Camera ready** |
*Convenience lights illuminate the corners of the cab for easier entry and exit.
** Starting with model year 2022, the Ultimate Visibility package is camera ready.
John Deere integrated solutions: a world of connected technology, right from the factory
Maximizing uptime using connectivity and technology
John Deere makes it easy for you to access an entire suite of connected applications, all designed to help you make the most of every seed, every hour, every gallon, and every bit of machine-related information.
Each 9 Series Tractor comes standard with the John Deere StarFire™ 6000 Integrated Receiver and Generation 4 CommandCenter™ display; there’s no need for setup, installation, or initial global positioning system (GPS) calibration. Integrated AutoTrac™ assisted steering gives you accurate, scalable guidance for low-stress operation in nearly any conditions and can improve field efficiency by 10 percent or more. The 9 Series Tractors also feature standard JDLink™ telematics and users can turn on connectivity in the John Deere Operations Center for anytime, anywhere access to critical machine and field information. And every tractor comes from the factory with John Deere Connected Support™, so you and your dealer can anticipate and address critical system needs.
From here? The sky’s the limit. Choose any of our operation-specific applications to help maximize efficiency and productivity during planting, tillage, or other field activities.
*NOTE: Ordering is temporarily unavailable for the StarFire 6000 Integrated Receiver. John Deere is diligently working to resolve this issue. Please watch the Price Pages and the announcements in the Sales Manual for updates. We apologize for any inconvenience.
 |
 |
 |
| StarFire 6000 Integrated Receiver | AutoTrac | JDLink |
Base equipment:
Optional equipment:
|
Base equipment:
Optional equipment:
|
Base equipment:
|
*Available with Premium Activation 3.0
**Available with Automation Activation 4.0
Work at your best with 9 Series Comfort and Convenience packages
Ultimate Comfort and Convenience package (shown on 8R Tractor)
When you’re spending dozens of hours per week in the cab, a comfortable operating environment isn’t just an option – the right features, in the right places, let you and your operators work at your best, dawn to dusk and beyond.
The 7, 8, and 9 Series Tractors offer three Comfort and Convenience packages to fit your needs: Select, Premium, and Ultimate. But regardless of which package you choose, you’ll still get the John Deere CommandARM™ console that puts critical controls within easy reach. You’ll get all the storage space you need for drinks, meals, and other stowable items. And you’ll have plenty of outlets to keep your electronics powered.
| Comfort and Convenience packages | Select | Premium | Ultimate |
| Seat |
|
|
|
| Infotainment |
|
|
|
| Business band ready | X | X | X |
| Four USB and one 12-V outlet | X | X | X |
| Dual tilt column | X | X | X |
| Footrests | --- | X | X |
| Refrigerator | --- | X | X |
| 120-V/300-W three-prong outlet | --- | X | X |
| Carpeted floor mat | --- | --- | X |
| Leather-wrapped steering wheel | --- | --- | X |
Bluetooth is a trademark of Bluetooth SIG, Inc. XM is a trademark of Sirius XM Radio Inc.
A range of hydraulic options give you the power and flexibility to take on your toughest applications
Selective control valves (SCVs) on a 9R Tractor
Of course, the 9 Series has the hydraulic muscle you need to push, pull, lift, and power your most demanding implements. But thanks to a range of enhancements to the hydraulic system, these tractors can provide that power at lower engine speeds, saving you fuel while still giving your implements the capacity they need. Regardless of model or configuration, the new 9 Series hydraulic system gives you:
- An increase of almost 40 percent in charge pump capacity, from 54-cc to 75-cc, to help maintain a higher flow at lower engine speeds
- A new swash plate angle sensor to monitor hydraulic flow and pressure and adjust engine speed to meet demand
- An integrated hydraulic pump, filter, and priority valve for fewer and shorter lines, reduced pressure loss, fewer flow restrictions, and an extra level of reliability
And if you depend on implements that need continuous hydraulic power, the 9 Series Tractors are available with Intelligent Power Management (IPM). Using dual pumps and advanced sensor and control technology, IPM provides additional engine and hydraulic power for high-demand applications like air seeding up and over hills or through thick, tough soil.
Add in single and dual pump options and a flexible number rear SCVs, and you can configure a powerful, fuel-efficient hydraulic system to meet the demands of your specific operation without paying for capacity you don’t need.
The new 9 Series: Easy to run, easy to maintain
9RX Tractor
When you’re trying to get a field planted before weather moves in, there’s no time to hit a scheduled maintenance interval or get smacked with an unexpected repair. That’s why we designed the 9 Series for maximum reliability and less in-season maintenance.
To start, we simplified as many systems as possible, using components common to other tractor lines and minimizing potential downtime due to parts availability. Then we eliminated as many potential pain points as possible through changes in the cooling, aftertreatment, and diagnostic systems, including:
- Replacing the fan drive system with a maintenance-free hydraulic fan drive
- Streamlining aftertreatment with a single-canister inline system that’s simpler and features fewer parts
- Improving uptime by adding better descriptions to diagnostic codes and offering predictive diagnostics through John Deere Expert Alerts
- A front-left service panel for easier access to engine oil check and fill points;
- Offering a 500-hour oil change interval on the John Deere JD14 (13.6L/827-cu in.) Final Tier 4 (FT4) engine when using approved John Deere oil and filter.
Specifications
Compare the specifications of up to 4 models
| Key Specs | 9rt-570 Current Model |
|---|---|
| Engine description | JD14 (B20 diesel compatible) |
| Engine displacement | 13.6 L 827 cu in. |
| Rated engine power | 419 kW 570 hp |
| Maximum engine power | 461 kW 627 hp |
| Rated PTO power (hp SAE) | 245 kW 329 hp |
| Maximum PTO power | |
| Transmission type | John Deere e18™ 18-speed PowerShift™ with Efficiency Manager™: 40 km/h 25 mph |
| Hydraulic pump rated output | Standard: 208 L/min 55 gpm Optional: 416 L/min 110 gpm |
| Rear hitch category (SAE designation) | Category 4N/N: 6804 kg 15,000 lb Category 4N/N: 9072 kg 20,000 lb |
| Base machine weight | 20,582 kg 45,375 lb |
| Maximum engine power PS (hp ISO) at max engine speed (EU 2016/1628) | |
| Rated engine power PS (hp ISO) at rated engine speed (EU 2016/1628) | |
| Engine specifications | |
| Description | JD14 (B20 diesel compatible) |
| Engine type | In-line six, four valve |
| Engine family | MJDXL13.5334 |
| Rated speed | 2100 rpm |
| Aspiration | Dual series turbocharger with fixed geometry first stage and wastegated second stage; air-to-air aftercooling and cooled exhaust gas recirculation (EGR) |
| Cylinders liners | Wet-sleeve |
| Emission level | Final Tier 4 (FT4) |
| After treatment type | Diesel oxidation catalyst (DOC)/selective catalytic reduction (SCR) |
| Displacement | 13.6 L 827 cu in. |
| Engine performance | |
| Rated power | 419 kW 570 hp |
| Rated PTO power (hp SAE) | 245 kW 329 hp |
| Maximum PTO power | |
| Intelligent Power Management (IPM) | |
| Power boost | 10 percent |
| Maximum engine power | 461 kW 627 hp |
| Engine peak torque | At 1550 rpm: 2631 Nm 1940 lb-ft |
| Drawbar power | |
| PTO torque rise | 38 percent |
| Fuel injection system and control | |
| Air cleaner type | |
| Maximum engine power PS (hp ISO) at max engine speed (EU 2016/1628) | |
| Rated engine power PS (hp ISO) at rated engine speed (EU 2016/1628) | |
| Transmission | |
| Type | John Deere e18 18-speed PowerShift with Efficiency Manager: 40 km/h 25 mph |
| Reverser | |
| Clutch; wet/dry | |
| Creeper | |
| Hydraulic system | |
| Type | Closed-center, pressure-and-flow compensated |
| Pump rated output | Standard: 208 L/min 55 gpm Optional: 416 L/min 110 gpm |
| Available flow at a single rear SCV | 1.3-cm (1/2-in.) couplers: 132 L/min 35 gpm 1.9-cm (3/4-in.) couplers: 159 L/min 42 gpm |
| Available flow at front SCVs | |
| Number of rear selective control valves (SCVs) | Four to eight factory or field installed Base: four 1.3-cm (1/2-in.) couplers Optional: five to six 1.3-cm (1/2-in.) couplers factory installed Optional: three 1.9-cm (3/4-in.) couplers plus five 1.3-cm (1/2-in.) couplers factory installed |
| Number of mid selective control valves (SCVs) | |
| Number of front selective control valves (SCVs) | |
| Joystick SCV control | |
| Auxiliary hydraulic features | |
| SCV control | Electronic |
| Rear hitch | |
| Hitch draft control load sense type | |
| Remote control valves available | |
| Hitch category (SAE designation) | Category 4N/N: 6804 kg 15,000 lb Category 4N/N: 9072 kg 20,000 lb |
| Maximum lift capacity behind lift points | Category 4N/4: 9072 kg 20,000 lb |
| Lift capacity at standard frame | |
| Sensing type | Electrohydraulic with draft sensing |
| Rear axle differential lock | |
| Drawbar | |
| Drawbar category | Standard: Category 5 with heavy-duty drawbar support Optional: Category 5 |
| Maximum vertical load | 5440 kg 12,000 lb |
| Rear power take-off (PTO) | |
| Type | Independent 44 mm (1.75 in.) 20-spline, 1000 rpm |
| Engine rpm (at rated PTO speeds) | |
| Economy PTO speeds | |
| Reverse PTO speeds | |
| Multispeed PTO option availability | |
| Ground speed PTO option availability | |
| PTO actuation | Electrohydraulic |
| Front hitch | |
| Category | |
| Electric power | |
| Standard lift capacity | |
| Front power take-off (PTO) | |
| PTO speed | |
| Rear axle | |
| Type | |
| Final drive type | Outboard planetary |
| Differential controls | |
| Axle type | |
| Brakes, type and control | |
| Rear differential lock | |
| Load rating | |
| Front axle | |
| Type | |
| Front axle differential lock | |
| Load rating | |
| Tires | |
| Rear | |
| Wheel tread range | |
| Turning radius with brakes | |
| Turning radius without brakes | |
| Central Tire Inflation System (CTIS) | |
| Front | |
| Tracks | |
| Tread spacing | |
| Drive type | Camso® 4500 and 6500 General Ag Series - friction drive track belts |
| Track width | Standard: 762 mm 30 in. Optional: 914 mm 36 in. |
| Mid-rollers | Four |
| Steering | |
| Brakes | |
| Primary brake (foot brake) | |
| Secondary brake | |
| Park lock | |
| MFWD braking | |
| Front axle brakes | |
| Auxiliary brakes | |
| Hydraulic trailer brakes | |
| Pneumatic trailer brakes | |
| Electrical system | |
| Alternator size | Standard: 250 amp Optional: 330 amp |
| Battery options | 12 V |
| Working lights | Standard: 18 halogen Optional: 18 or 24 LED plus 8 LED conveninence lights |
| Type of bulb in headlight (Halogen, Zenon, LED) | Standard: halogen, 65 W Optional: LED |
| Type of bulb in beacon (Halogen, Zenon, LED) | |
| dB(A) rating for backup alarm | |
| Total cold cranking amps | 3 x 925 CCA Total: 2775 CCA |
| Operator station | |
| Rollover protective structure, OOS | |
| Seat | Degree of seat swivel, left hand 25 degree (angle) Degree of seat swivel, right hand 25 degree (angle) Air suspension |
| Cab suspension | |
| Instructional seat | Standard |
| Display | Standard: Generation 4 4600 CommandCenter™: 25.4 cm 10 in. Optional: Extended monitor |
| Radio | Standard: AM/FM stereo with weatherband, remote controls, auxiliary input jack, four speakers and external antenna Optional: Touchscreen radio |
| Inner cab volume | 3.27 m3 115 cu ft |
| dB(A) rating | |
| Cab glass area | 6.64 m2 71.47 sq ft |
| Safety glass rating | |
| Front visibility | |
| Dimensions | |
| Wheelbase | 2947 mm 116 in. |
| Overall width | |
| Overall length | With front weights, excluding hitch and coupler: 6965 mm 274.2 in. With front weights, including hitch and coupler: 7201 mm 283.5 in. |
| Overall height | |
| Drawbar clearance | 381 mm 15 in. |
| Front axle center | |
| Approximate shipping weight, Open;Cab | 20,582 kg 45,375 lb |
| Weight | |
| Base machine weight | 20,582 kg 45,375 lb |
| Maximum ballast level | 24,494 kg 54,000 lb |
| Maximum permissible weight | |
| Capacities | |
| Crankcase oil volume | 64 L 16.9 U.S. gal. |
| Fuel tank | 1324 L 350 U.S. gal. |
| Diesel exhaust fluid (DEF) tank | 93.9 L 24.8 U.S. gal. |
| Cooling system | 56.5 L 14.9 U.S. gal. |
| Transmission-hydraulic system | With 3-point hitch and PTO: 307.8 L 81.3 U.S. gal. Without 3-point hitch and PTO: 300 L 79.3 U.S. gal. |
| Serviceability | |
| Interval for engine oil change | 500 hours |
| Interval for hydraulic/transmission oil change | 1500 hours |
| Interval for engine coolant change | 6000 hours |
| Loaders | |
| Loader | |
| Lift capacity at full height | |
| Maximum lift height | |
| Leveling type | |
| Precision AG | |
| Guidance | Integrated AutoTrac™ |
| Telematic | Available with JDLink™ hardware, activations, and Ethernet harnesses (availability dependent upon destination) |
| Remote diagnostics | Available with activated JDLink hardware and activations |
| Miscellaneous | |
| AutoTrac ready | |
| ISOBUS ready | |
| CommandCenter video inputs | |
| Immobilizer | |
| Side slope rating | |
| Uphill/downhill slope rating | |
| Country of manufacture | USA |
Accessories and Attachments
Cab Operator's Station
Cell phones, tablets, and other devices are key tools for farming today. John Deere has now made it easier than ever to incorporate these tools into the operator's station.
Stay connected with the RAM® cell phone and tablet mounts. John Deere offers a vast selection of adjustable accessory mounting solutions and media devices to fit every need and application.
Mounting bracket with cell phone and tablet mount
Mounting bracket with cell phone and tablet mount
RAM is a trademark of National Products Inc.
Carpet floor mat
Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.
Cell phones, tablets, and other devices are key tools for farming today. John Deere has now made it easier than ever to incorporate these tools into the operator's station.
Stay connected with the RAM® cell phone and tablet mounts. John Deere offers a vast selection of adjustable accessory mounting solutions and media devices to fit every need and application.
Mounting bracket with cell phone and tablet mount
Mounting bracket with cell phone and tablet mount
RAM is a trademark of National Products Inc.
GreenStar 3 2630 Display shown
Use the tables below to find all the parts needed to connect GreenStar displays physically and electronically.
For GreenStar 2 CommandCenter™ 2600/GreenStar 3 2630 Displays:
Mounting style |
Display mount (ball) |
Tie-rod assembly |
Rail mount (ball) |
Clamp |
PF11019 plus two 19M8648 |
RE574454 |
AXE59372 |
10-mm (0.4-in.) threaded |
PF11019 plus two 19M8648 |
PF80459 |
RE576490 |
|
|||
Single location bracket |
RE558242 |
||
The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575).
NOTE: Also order power harness (PF90686) and Ethernet cable (PFP12950). Optional protective film for screen (PF90596) is also available.
For 4240 /4640 Universal Display and Extended Monitor:
Mounting style |
Display mount (ball) |
Tie-rod assembly |
Rail mount (ball) |
Clamp |
AL212683 plus four 19M8648 |
AXE59372 |
|
10-mm (0.4-in.) threaded |
UC17356 plus four 19M8648 |
PF80459 |
RE576490 |
|
|||
Single location bracket |
RE558242 |
||
The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575).
NOTE: Also order power harness (PFP12435) and Ethernet cable (RE573617). Optional protective film for screen (PF90596) is also available.
BRE10501 CommandARM bracket
This unique bracket connects to the right side of the CommandARM. It is compatible with the cell phone mount (BRE10015), tablet mount (BRE10255), and more. It is also compatible with the touchscreen radio relocation kit (BXX11045) for Premium and Ultimate Comfort and Convenience packages.
Cup Holder Kit - 9420RWBXX10883
The floor insulation kit can reduce cab heat generated by transmission and hydraulic oil temperatures below the cab floor. It can reduce the overall cab temperature, as it works as a thermal barrier. The product comes in a large sheet, which is easily cut to fit the contours of the cab floor.
The kit is large enough to fit the floor pan design of 6 through 9 Series Tractor cabs.
Foot decelerator next to pedals
BXX10810 foot decelerator kit
The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.
BRE10458 footrest kit with three pegs
Foot peg on the steering column
The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.
The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.
Features:
- Direct bolt-on factory finish – no drilling or cutting required
- Heavy gauge steel to support any operator
- Color-matched rubber surfaces for comfort and vibration reduction
- Model year 2022 and newer are compatible with the extension and adjustment kit (BRE10511)
Foot-Operated Speed Control - 9420RWBXX10812
Headliner Mounting Rail - 9420RWR572009
R562310 harness routing hook (shown mounted to headliner rail R558980 and using retention features of the C-post)
Harness routing hook
Keep accessory and monitor wiring neatly contained with these moveable harness hooks. These hooks are specifically designed to easily snap into the factory headliner rail and BRE10574 window mounting bracket and rail with no tools and can be moved as needed. These hooks allow accessory wiring to routed together for a clean look and maximized visibility.
RE584990 leather steering wheel
Close-up of leather steering wheel
Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.
AL212683 tie-rod assembly with mounting plates
PF80459 117.6-mm (4.63-in.) tie-rod assembly
PF80460 38.1-mm (1.5-in.) ball mount on U-bolt
RE574454 76.2-mm (3-in.) tie-rod assembly with 38.1-mm (1.5-in.) ball on round mounting plate
UC17356 38.1-mm (1.5-in.) ball mount on universal square
RE558821 25.4-mm (1-in.) ball mount on 10-mm (0.4-in.) stud
AXE59372 clamp-style accessory mounting bracket
BRE10482 25.4-mm (1-in.) T-slot ball mount assembly (left) and BRE10483 38.1-mm (1.5-in.) T-slot ball mount assembly
There are a variety of additional mounting part solutions available through John Deere to resolve unique mounting configuration needs. The table below includes several additional parts (not shown above) to aid in many different mounting needs.
GreenStar 3 2630 Display shown
Use the tables below to find all the parts needed to connect GreenStar displays physically and electronically.
For GreenStar 2 CommandCenter™ 2600/GreenStar 3 2630 Displays:
Mounting style |
Display mount (ball) |
Tie-rod assembly |
Rail mount (ball) |
Clamp |
PF11019 plus two 19M8648 |
RE574454 |
AXE59372 |
10-mm (0.4-in.) threaded |
PF11019 plus two 19M8648 |
PF80459 |
RE576490 |
|
|||
Single location bracket |
RE558242 |
||
The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575).
NOTE: Also order power harness (PF90686) and Ethernet cable (PFP12950). Optional protective film for screen (PF90596) is also available.
For 4240 /4640 Universal Display and Extended Monitor:
Mounting style |
Display mount (ball) |
Tie-rod assembly |
Rail mount (ball) |
Clamp |
AL212683 plus four 19M8648 |
AXE59372 |
|
10-mm (0.4-in.) threaded |
UC17356 plus four 19M8648 |
PF80459 |
RE576490 |
|
|||
Single location bracket |
RE558242 |
||
The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575).
NOTE: Also order power harness (PFP12435) and Ethernet cable (RE573617). Optional protective film for screen (PF90596) is also available.
Refrigerator
Keep food and drinks cool with refrigerator
The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists, and no software is required to complete the install.
BRE10574 assembly with steel bracket (A) and mounting rail (B)
A large steel bracket, which spans the entire right-side window, mounts directly to the cab frame for rigidity and strength. The headliner mounting rail (included in this kit) is bolted to the steel bracket. This solution enables the operator to configure and reconfigure monitors and accessories without changing mounting solutions from either location. This rail accommodates clamp-style and T-slot style mount solutions (purchased separately).
- Spans the entire right-side window.
- Uses the same factory headliner mounting rail part number (R558980) for easy reconfiguring of accessories.
- Aluminum mounting rail mounts to either the top or underside of the steel bracket, allowing even more options and maximizing visibility preferences.
- Compatible with AXE59372 (clamp-style mount) and BRE10482 and BRE10483 (T-slot ball mounts).
Secondary Hitch Controls - 9420RWBRE10437
A favorite worldwide, the RAM self-leveling cup holder is now available as a kit - designed specifically for Deere equipment. It is easily installed to keep your favorite beverage upright even in the roughest terrain. The perfect accessory for any cab that has 10-mm mounting bosses.
Self-leveling cup holder John Deere branded beverage insulator included
The new cup holder features a unique self-leveling design. This pivoting design allows easy adjustment for the holder while offsetting motion of the vehicle when moving.
Features and applications:
- Self-leveling action reduces spills
- Durable design for rough environments
- Easy adjustable mounting for ideal placement
- Includes John Deere branded beverage insulator
- Compatible with most monitor brackets and all 10-mm threaded bosses
BRE10575 short vertical rail (mounted in right front upper A-post)
Short vertical rail (mounted in right lower rear C-post)
Short vertical rail (mounted in left rear C-post)
A shorter, 260-mm (10.25-in.) aluminum mounting rail is available. The kit includes all the hardware needed to mount in up to five vertical locations, including upper and lower right-side A-post rollover protective structure (ROPS), upper right-side C-post ROPS, and upper left rear C-post ROPS. It is compatible with both clamp-style and t-slotted ball mounts (purchased separately).
- Up to five vertical locations supported with this one rail (kit contains one rail and mounting hardware).
- Uses the same factory headliner mounting rail shape for ease of operator adjustment and preferences.
- Works in combination with other accessory bracket solutions.
- Compatible with AXE59372 (clamp-style mount) and BRE10482 and BRE10483 (T-slot ball mounts).
BRE10436 multifunction lever (shown in model year 2018 7R Tractor)
This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.
StarFire 6000 Locking Bracket - 9420RWBPF11074
RE275532 storage container
Storage container mounting location
This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right-side window.
RE593670 sun shade shown
The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.
BRE10255 tablet mount assembly (1), BRE10015 cell phone mount assembly (2), and RE343680 L-shaped mounting bracket (3)
BRE10152 self-leveling cup holder assembly
BXE10606 locking suction mount cell phone assembly
BXE10607 locking suction mount tablet assembly
BRE10255 tablet mount assembly
BXE10864 tablet mount assembly
Mounting a tablet, cell phone, or beverage can be easily done with these solutions. These strong and simple-to-use solutions keep all important items right where they are wanted.
R569171 door lock handle
Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.
Connectivity Hardware
ISO 11783 location in model year 2011 to 2020 R Series Tractor cab
ISO 11783 location in model year 2020 7R and 8R/8RT/8RX (with updated cab) and model year 2022 and newer 9R/9RT/9RX
RE322780 ISO cab implement CAN bus adapter
The ISO cab implement CAN bus adapter is available to connect any ISO compliant implement or device to an 8R, 8RT, 9R, 9RT, and 9RX (including Scraper Special) Tractor. These connectors are commonly used for planter frame control boxes.
Refer to the operator's manual, sections 16 (CommandCenter™) and 25 (Operator Station), for additional information on ISO implements.
NOTE: If the harness is not in use, unplug it from the ISO 11783 location or plug the four-pin connectors together on the harness. If neither of these are done, implement CAN communication errors occur.
StarFire mounting bracket
The model year 2020 and newer large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or StarFire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.
RTK Bracket Kit - 9420RWBRE10512
DISPLAY HARDWARE
Display Harness - GS2 / GS3 Display with Video to GreenStar™ (Round) Cornerpost 762 mm (30 in.) - 9420RWPFP12435
Ethernet cable
This cable connects the cornerpost Ethernet connector (square) to the GreenStar™ 3 2630 Display Ethernet connector (round). It is required for used with Remote Display Access (RDA), Wireless Data Transfer (WDT), and Machine Sync.
The square-to-round connector cable is 80-cm (31.5-in.) long.
Gen 4 and GreenStar™ Displays Bracket for Single Display - Tractor and Sprayer - 9420RWBPF12124
GreenStar™/Gen4 - 254 mm (10 in.) Display Touch Panel Protector Service Kit - 9420RWPF90596
Harness - Original GreenStar™ Display and Mobile Processor to GreenStar™ 3 or GreenStar™ 2 (Round) Cornerpost - 9420RWPF90686
Drawbar
Drawbar reinforcement kit
Wide swing drawbar support kit
Bottom roller kits
Drawbar reinforcement kits are designed to handle heavy vertical loads such as large drawn planters, grain carts, trailer tanks, and large drawn rippers. Category 5 drawbars are base equipment and have a 4581-kg (10,100-lb) static vertical load capacity. Installation of the drawbar reinforcement kit raises the maximum static vertical load.
Quick-attach drawbar - 9420RWCB21494061
Hydraulic hose support
This field-installed option reduces stress on the couplers by providing support to the heavy hydraulic hoses used in scraper application. The hydraulic hose support attaches to the back of the tractor next to the drawbar.
Electrical
3-pin octagonal to 3-pin round convenience outlet (flat pins) single device adapter - 9420RWRE596959
NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.
Carpet floor mat
Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.
Foot throttle next to pedals
BRE10440 foot throttle kit
The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.
Foot decelerator next to pedals
BXX10810 foot decelerator kit
The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.
BRE10458 footrest kit with three pegs
Foot peg on the steering column
The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.
The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.
Features:
- Direct bolt-on factory finish – no drilling or cutting required
- Heavy gauge steel to support any operator
- Color-matched rubber surfaces for comfort and vibration reduction
- Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)
RE593670 sun shade shown
The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.
Storage container with lid/ashtray
RE275532 storage container
Storage container mounting location
This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.
Leather-wrapped steering wheel
RE584990 leather steering wheel
Close-up of leather steering wheel
Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.
Refrigerator
Keep food and drinks cool with refrigerator
The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.
RE588734 internal rear mirror (shown in standard mounting position)
The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.
Type A/B style socket inverter kit (type C style is similar)
Cab power inverter kit
These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update.
Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)
RE596958 complete John Deere power strip for model year 2020 and newer cabs
The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.
Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter
RE596959 power adapter
For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.
A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.
Harness adapter for citizen band (CB) power connection
Antenna coax and power connector base prewired in the cab
Harness adapter for power connection
Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.
Amp-to-flying leads power connector
RE37651 power connector
This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.
Amp-to-John Deere power outlet adapter
RE67015 outlet adapter
This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.
External StarFire™ mounting bracket
StarFire mounting bracket
The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.
Front license plate mounting bracket
License plate mounting bracket (front)
This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.
Vandal protection door locks with custom key
R569171 door lock handle
Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.
Joystick (multifunction lever)
BRE10436 multifunction lever (shown in model year 2018 7R Tractor)
This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.
Subwoofer
Tweeters
Amplifier
Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.
The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.
Touchscreen radio relocation kit
BXX11045 touchscreen radio relocation kit
Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.
Features:
- Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
- Fine-tune the position adjustment with the locking knob on the tie rod
Touchscreen video camera upgrade kit
Touchscreen video camera upgrade kit
Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.
NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.
NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.
Carpet floor mat
Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.
Foot throttle next to pedals
BRE10440 foot throttle kit
The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.
Foot decelerator next to pedals
BXX10810 foot decelerator kit
The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.
BRE10458 footrest kit with three pegs
Foot peg on the steering column
The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.
The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.
Features:
- Direct bolt-on factory finish – no drilling or cutting required
- Heavy gauge steel to support any operator
- Color-matched rubber surfaces for comfort and vibration reduction
- Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)
RE593670 sun shade shown
The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.
Storage container with lid/ashtray
RE275532 storage container
Storage container mounting location
This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.
Leather-wrapped steering wheel
RE584990 leather steering wheel
Close-up of leather steering wheel
Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.
Refrigerator
Keep food and drinks cool with refrigerator
The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.
RE588734 internal rear mirror (shown in standard mounting position)
The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.
Type A/B style socket inverter kit (type C style is similar)
Cab power inverter kit
These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update.
Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)
RE596958 complete John Deere power strip for model year 2020 and newer cabs
The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.
Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter
RE596959 power adapter
For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.
A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.
Harness adapter for citizen band (CB) power connection
Antenna coax and power connector base prewired in the cab
Harness adapter for power connection
Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.
Amp-to-flying leads power connector
RE37651 power connector
This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.
Amp-to-John Deere power outlet adapter
RE67015 outlet adapter
This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.
External StarFire™ mounting bracket
StarFire mounting bracket
The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.
Front license plate mounting bracket
License plate mounting bracket (front)
This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.
Vandal protection door locks with custom key
R569171 door lock handle
Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.
Joystick (multifunction lever)
BRE10436 multifunction lever (shown in model year 2018 7R Tractor)
This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.
Subwoofer
Tweeters
Amplifier
Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.
The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.
Touchscreen radio relocation kit
BXX11045 touchscreen radio relocation kit
Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.
Features:
- Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
- Fine-tune the position adjustment with the locking knob on the tie rod
Touchscreen video camera upgrade kit
Touchscreen video camera upgrade kit
Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.
NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.
9-pin electrical connector
The nine-pin electrical connector is required to allow TouchSet depth control to be used on implements with this feature. The harness provides a position input to the tractor selective control valve (SCV) unit that enables the TouchSet system.
This feature allows the operator to adjust height and depth of remote lift cylinders by using the TouchSet controls in the cab.
Type A/B style socket inverter kit (type C style is similar)
Cab power inverter kit
These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update.
NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.
Carpet floor mat
Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.
Foot throttle next to pedals
BRE10440 foot throttle kit
The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.
Foot decelerator next to pedals
BXX10810 foot decelerator kit
The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.
BRE10458 footrest kit with three pegs
Foot peg on the steering column
The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.
The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.
Features:
- Direct bolt-on factory finish – no drilling or cutting required
- Heavy gauge steel to support any operator
- Color-matched rubber surfaces for comfort and vibration reduction
- Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)
RE593670 sun shade shown
The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.
Storage container with lid/ashtray
RE275532 storage container
Storage container mounting location
This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.
Leather-wrapped steering wheel
RE584990 leather steering wheel
Close-up of leather steering wheel
Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.
Refrigerator
Keep food and drinks cool with refrigerator
The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.
RE588734 internal rear mirror (shown in standard mounting position)
The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.
Type A/B style socket inverter kit (type C style is similar)
Cab power inverter kit
These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update.
Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)
RE596958 complete John Deere power strip for model year 2020 and newer cabs
The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.
Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter
RE596959 power adapter
For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.
A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.
Harness adapter for citizen band (CB) power connection
Antenna coax and power connector base prewired in the cab
Harness adapter for power connection
Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.
Amp-to-flying leads power connector
RE37651 power connector
This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.
Amp-to-John Deere power outlet adapter
RE67015 outlet adapter
This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.
External StarFire™ mounting bracket
StarFire mounting bracket
The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.
Front license plate mounting bracket
License plate mounting bracket (front)
This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.
Vandal protection door locks with custom key
R569171 door lock handle
Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.
Joystick (multifunction lever)
BRE10436 multifunction lever (shown in model year 2018 7R Tractor)
This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.
Subwoofer
Tweeters
Amplifier
Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.
The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.
Touchscreen radio relocation kit
BXX11045 touchscreen radio relocation kit
Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.
Features:
- Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
- Fine-tune the position adjustment with the locking knob on the tie rod
Touchscreen video camera upgrade kit
Touchscreen video camera upgrade kit
Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.
NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.
Video camera Kit (Front visibility) - 9420RWBXX10207
Video camera Kit (Rear visibility) - 9420RWBXX10206
Engine
Frame
Tow cable front hook
Rear tow cable connection point
The front tow cable is recommended for pulling all 9 Series Tractors in time of needed assistance. Tow cables are available as a factory-installed option on all ag tractors and are base equipment on all Scraper Special Tractors. The tow cable attaches to the area in front of the drawbar and is also available as a field-installed option.
Front Weights
Hydraulic Selective Control Valves (SCVs)
For implements that require high hydraulic flow, 19-mm (3/4-in.) couplers are available in two configurations.
A single 19-mm (3/4-in.) selective control valve (SCV) coupler is available as a field-installed attachment for dual-pump, 435-L/min (115-gpm) hydraulic systems.
19-mm (3/4-in.) coupler
Hydraulic Intelligent Power Management (IPM) with three 19-mm (3/4-in.) and five 12.7-mm (1/2-in.) SCV couplers are available as a factory- or field-installed attachment on 9620R and 9620RX Tractors equipped with dual-pump, 435-L/min (115-gpm) hydraulic systems.
Color-coded SCVs
Five remote SCVs
The field-installed electronic SCV kits are made available for tractors needing additional SCVs. These kits provide metered flow rates and timed detents with pressure and load sense compensation. The additional SCV(s) can also be integrated into the Headland Management System.
The field-installed kit includes International Organization for Standardization (ISO) lever-assisted breakaway couplers and armrest control lever.
Five remote SCVs
The field-installed electronic SCV kits are made available for tractors needing additional SCVs. These kits provide metered flow rates and timed detents with pressure and load sense compensation. The additional SCV(s) can also be integrated into the Headland Management System.
The field-installed kit includes International Organization for Standardization (ISO) lever-assisted breakaway couplers and armrest control lever.
Five remote SCVs
The field-installed electronic SCV kits are made available for tractors needing additional SCVs. These kits provide metered flow rates and timed detents with pressure and load sense compensation. The additional SCV(s) can also be integrated into the Headland Management System.
The field-installed kit includes International Organization for Standardization (ISO) lever-assisted breakaway couplers and armrest control lever.
Hydraulics
Easy hookup of planters and other implements
48-gpm SCV stack on a 9020 Series Tractor
78-gpm SCV stack on a 9020 Series Tractor
Attaching implement hydraulic hoses to locations on the tractor other than into an SCV has always been a challenge to know what kits are required for compatibility. Getting them installed in a timely manner can at times be confusing and time consuming.
To assist in making hookup to large planters, seeders, and harvesting equipment where multiple connections are required, there are now factory-installed auxiliary hydraulic couplers on wheel tractors.
Auxiliary sump coupler
For applications requiring low return oil back pressure (10 psi or less), the sump coupler kit allows oil to return directly to reservoir (differential case) from hydraulic motor, bypassing the remote coupler and SCV. When connecting motor case or seal return hose to coupler, make sure hose end and coupler are clean.
This coupler is required for correct attachment to current-production seeding products with case drain lines.
Hydraulic motor return couplers
The hydraulic motor return couplers can be used as a coupler for return oil flow, from hydraulic orbital motors and other devices, to the tractor's low-pressure return port, labeled ''R'' on the tractor.
Use of this connector specifically in the return to sump port position is for hydraulic components that require a ''leak-off line'' connection to the tractor. Components and implements that require this typically are larger orbital motors that require a drain for seal protection. The connector in the sump port is not to be used to carry return flow from a function to the tractor.
Power beyond couplers
Power beyond provides live hydraulic power to equipment. This kit supplies oil pressure to implements when the engine is running.
Any implement using power beyond must have a way to control oil flow. Use an independent control valve that is pressure and flow compensating (supplied separately) to control the oil flow rate from this coupler set.
The auxiliary hydraulic optional equipment includes the following:
A - Power beyond couplers
B - Hydraulic motor return couplers
C - Motor seal drain kit
D - Load sense coupler
NOTE: RE151894 and RE67182 cannot be used together.
Easy hookup of planters and other implements
48-gpm SCV stack on a 9020 Series Tractor
78-gpm SCV stack on a 9020 Series Tractor
Attaching implement hydraulic hoses to locations on the tractor other than into an SCV has always been a challenge to know what kits are required for compatibility. Getting them installed in a timely manner can at times be confusing and time consuming.
To assist in making hookup to large planters, seeders, and harvesting equipment where multiple connections are required, there are now factory-installed auxiliary hydraulic couplers on wheel tractors.
Auxiliary sump coupler
For applications requiring low return oil back pressure (10 psi or less), the sump coupler kit allows oil to return directly to reservoir (differential case) from hydraulic motor, bypassing the remote coupler and SCV. When connecting motor case or seal return hose to coupler, make sure hose end and coupler are clean.
This coupler is required for correct attachment to current-production seeding products with case drain lines.
Hydraulic motor return couplers
The hydraulic motor return couplers can be used as a coupler for return oil flow, from hydraulic orbital motors and other devices, to the tractor's low-pressure return port, labeled ''R'' on the tractor.
Use of this connector specifically in the return to sump port position is for hydraulic components that require a ''leak-off line'' connection to the tractor. Components and implements that require this typically are larger orbital motors that require a drain for seal protection. The connector in the sump port is not to be used to carry return flow from a function to the tractor.
Power beyond couplers
Power beyond provides live hydraulic power to equipment. This kit supplies oil pressure to implements when the engine is running.
Any implement using power beyond must have a way to control oil flow. Use an independent control valve that is pressure and flow compensating (supplied separately) to control the oil flow rate from this coupler set.
The auxiliary hydraulic optional equipment includes the following:
A - Power beyond couplers
B - Hydraulic motor return couplers
C - Motor seal drain kit
D - Load sense coupler
NOTE: RE151894 and RE67182 cannot be used together.
Easy hookup of planters and other implements
48-gpm SCV stack on a 9020 Series Tractor
78-gpm SCV stack on a 9020 Series Tractor
Attaching implement hydraulic hoses to locations on the tractor other than into an SCV has always been a challenge to know what kits are required for compatibility. Getting them installed in a timely manner can at times be confusing and time consuming.
To assist in making hookup to large planters, seeders, and harvesting equipment where multiple connections are required, there are now factory-installed auxiliary hydraulic couplers on wheel tractors.
Auxiliary sump coupler
For applications requiring low return oil back pressure (10 psi or less), the sump coupler kit allows oil to return directly to reservoir (differential case) from hydraulic motor, bypassing the remote coupler and SCV. When connecting motor case or seal return hose to coupler, make sure hose end and coupler are clean.
This coupler is required for correct attachment to current-production seeding products with case drain lines.
Hydraulic motor return couplers
The hydraulic motor return couplers can be used as a coupler for return oil flow, from hydraulic orbital motors and other devices, to the tractor's low-pressure return port, labeled ''R'' on the tractor.
Use of this connector specifically in the return to sump port position is for hydraulic components that require a ''leak-off line'' connection to the tractor. Components and implements that require this typically are larger orbital motors that require a drain for seal protection. The connector in the sump port is not to be used to carry return flow from a function to the tractor.
Power beyond couplers
Power beyond provides live hydraulic power to equipment. This kit supplies oil pressure to implements when the engine is running.
Any implement using power beyond must have a way to control oil flow. Use an independent control valve that is pressure and flow compensating (supplied separately) to control the oil flow rate from this coupler set.
The auxiliary hydraulic optional equipment includes the following:
A - Power beyond couplers
B - Hydraulic motor return couplers
C - Motor seal drain kit
D - Load sense coupler
NOTE: RE151894 and RE67182 cannot be used together.
Lighting
Auxiliary light kit
Auxiliary light kit
A rear fender, rear-facing work light is available for the tractor. The kit comes with mounting hardware and a harness which directly connects to the tractor’s existing chassis harness.
This mounting location allows for illumination of the hitch and drawbar area to aid in making connections to implements when natural lighting conditions are poor.
Convenience Lighting Cab Kit - 9420RWBXX10708
BRE10445 cab roof work lighting - shown from left rear corner
Increase light output over halogen work lights with this four-light kit for the front and rear roof corners of the cab. These lights are the same parts included in the Premium and Ultimate Visibility package and are a plug-and-play update. Eliminate bulb replacements while increasing color temperature and lumen output with this eight-light LED upgrade.
Mirrors
RE588734 internal rear mirror (shown in standard mounting position)
The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.
Power Take-Off (PTO)
44.5-mm (1.75-in.), 1000-rpm PTO
PTO and shield
- Available on all 9R and 9RT Ag Tractors regardless of transmission.
- Full-power capability for maximum utilization (9R Tractors derate to 238 PTO kW [319 PTO hp] when tractor is stationary)
- 44.5-mm (1.75-in.) diameter shaft
Electrohydraulic PTO control
The 9R Tractors utilize an electrohydraulic PTO engagement switch to activate the optional 1000-rpm PTO.
Radio
Touchscreen video camera upgrade kit
Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.
Subwoofer
Tweeters
Amplifier
Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.
The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.
Touchscreen Radio Relocation kit (Alternative Mount) - 9420RWBRE10364
Rear Hitch
Category 4/4N Quik Coupler Kit - 9420RWBRE10457
Quik-Hitch coupler
The hitch/coupler allows for quick, no-hassle hookups to many popular integral implements.
Features include:
- Tubular and box-welded steel construction
- Heat-treated bushings to prevent cracking and breakage
- Heat-treated hooks for long wear life
- Locking handles that rotate 100 degrees to open the locking lugs for easy implement release
- Hardened and zinc-plated steel alloy pins to take the shock of heavy loads and withstand exposure to the elements
Conversion kit
A Category 5 to Category 4 drawbar conversion kit is available for producers who have Category 4 implements that cannot be converted to Category 5.
The preferred method when operating high-horsepower tractors is to convert implements to Category 5.
For additional implement information, reference the planting and seeding or the tillage information.
Electro-Hydraulic 3 Point Hitch, 2 Track - 9420RWBRE10402
Greaseable pin kit
The rear hitch has pin joints located in the top lift carrier that uses pins (R304684) which can wear and require replacing to restore smooth operation over time.
The heavy-duty greasable pin kit provides a greasing zerk fitting on each pin for a grease shot to be included as part of the tractor’s grease maintenance.
This kit allows for the pin replacement to last far longer than the standard installed pin so long as it is regularly greased. This update will reduce or eliminate the need for future pin replacement in this joint.
Trailer Brake
Add a trailer brake system into the machine to safely and correctly connect the implement’s braking system. This kit allows operators to slow the tractor and the implement together, which is especially helpful for heavy road transport and to manage larger implements while maintaining good stopping power.
Always follow correct service intervals and perform required maintenance on the implement braking system by following the implement operator’s manual.
Transmission
Back Up Alarm Kit - 9420RWRE273380
Wheel and four-track mounting bracket
Two-track mounting bracket
Dual-beam radar sensor
See your true ground speed by adding a dual-beam radar. Select the correct mounting bracket for the tractor based on the drivetrain configuration, which includes a perfect fit bracket, harness, and hardware.
Wheel and four-track mounting bracket
Two-track mounting bracket
Dual-beam radar sensor
See your true ground speed by adding a dual-beam radar. Select the correct mounting bracket for the tractor based on the drivetrain configuration, which includes a perfect fit bracket, harness, and hardware.
Transmission Changeover/Conversion kit - 9420RWRE575961
Weights
Center Link Bracket for Monoblock - 9420RWBL15085
One Left Side Narrow Profile Track Frame Weight Bracket - 9420RWRE341174
One Right Side Narrow Profile Track Frame Weight Bracket - 9420RWRE341175
Frame weights
Quik-Tatch™ front weights are used to obtain the correct weight split to counterbalance rear-mounted implements. Each weight (R127764) weighs approximately 43 kg (95 lb). Weight support is designed to hold up to 26 Quik-Tatch weights.
IMPORTANT: Do not exceed 22,680 kg (53,000 lb) when ballasting 9030T Series Track Tractors.
Front weights provide additional ballast for the front axle
Front support with suitcase weights
Cast Quik-Tatch suitcase weights (R127764) can be added to provide additional ballast for implements that exert heavy draft loads and require additional ballast or with hitch-mounted implements that require additional ballast to maintain steering control while transporting.
These weights are Quik-Tatch weights that require minimal effort to attach.
Pickup weights
Pickup weights
Pickup weights are designed to add fast weight to the tractor. The following pickup weights can be mounted at the front.
Support (base weight):
- 900-kg (1948-lb) pickup weight
- 1150-kg (2535.3-lb) pickup weight
All pickup hitches can also be mounted at the rear in the 3-point hitch as a counter weight. To use the third mounting point, an additional center-link bracket is available.
1500-kg (3307-lb) and 1800-kg (3968.3-lb) pickup weights
The two weights differ only internally, therefore no external differences are visible.
The pickup weights can either be installed on the rear hitch or on the front hitch of the tractor using the center-link bracket. They cannot be mounted directly on the front base weight. A front hitch is required. The center-link bracket for installation is included.
The shape of the 1500-kg (3307-lb) and 1800-kg (3968.3-lb) pick-up weights allows for quick and safe mounting. This is ensured by an optimal alignment of the weight and the tractor along with a self-centering design.
Major benefits of the design:
- Easy and comfortable
- Less time is required
- Lower risk of injury
Due to the user-friendliness, an optimal ballasting of the tractor is guaranteed at any time.
The performance of the tractor is used to a greater extent, which leads to higher productivity and a reduction in fuel consumption.
The weights cannot be front installed in combination with Quik-Tatch front weights.
NOTE: Ballast should be limited by the lowest of either tire capacity or tractor capacity. The carrying capacity of each tire should not be exceeded. For more ballasting information refer to the Operator's Manual and ballast calculator.
Pick Up Weight 900 kg (1984 lb) Monoblock - 9420RWBL15083
Noncurrent attachment
Note: This is a noncurrent kit. The information provided is valid for each tractor as of the last date that tractor was in production.
Quik-Tatch weights are used to better ballast tractors for both field and loader applications.
Applies to tractor models:
-
Maximum of 4 weights on 2040, 6 weights on 2240, and 8 weights on 2440 and 2640 Tractors.
-
Maximum of 10 weights per tractor on 2840, 2940, 3150, 4030, 4040, 4230, 4240, 4430, and 4630 Tractors.
-
Maximum of 6 weights on 2355N; 8 weights on 2555 Low-Profile, 2755 Low-Profile, and 2855N.
-
Maximum of 4 weights on 2155, 6 weights on 2355, and 8 weights on 2555 and 2755 Tractors.
-
Maximum of 10 weights on 2955 and 12 weights on 2955 Tractors equipped with high lift capacity.
-
Maximum of 14 weights on 4440 Tractors.
-
Maximum of 20 weights on 4640 and 4840 Tractors.
-
Maximum of 14 weights on 4055 and 20 weights on 4255 and 4455 Tractors.
-
Maximum of 20 weights on 4555, 4560, 4755, 4760, 4955 and 4960 Tractors.
-
Weights only for 7200, 7400,7600, 7700 and 7800 Tractors.
-
Weight support only for 7600 (SN -7754), 7700 (SN -9088), 7800 (SN -14027) Tractors. For all 7200 and 7400 Tractors and 7600 MFWD (SN7755- ), 7700 MFWD (SN9089- ), and 7800 MFWD (SN14028- ): R129660 shown.
R129660 - Quick-Tatch Weight
Wheel Weights
Field-installed weight for tractors that require additional weight
8345RT Series shown with idler weight
Front idler starter weights can be used by operators as a starter weight to add additional idler weights to the front of a track tractor to offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor.
One pair of starter weights is required per idler to add additional wheel weights on the inside and outside of the front idler wheel.
NOTES:
1. Starter weight is required to install additional wheel weights on the idler.
2. Order attaching hardware through Parts.