3032E
Compact Utility Tractor
3-series-compact-tractors
- Standard four-wheel drive(4WD) for maximum traction
- Hydro transmission with Twin Touch™ pedals for ease of use
- Category 1 3-pt hitch compatible with dozens of implements
Apply For FinancingBuy OnlineMaintenance Plans
Pricing excludes attachments
View Product Brochure
10 Year Warranty Details
60 Day Promise
Features
Specifications
Compare the specifications of up to 4 models
Key Specs | 3032e Current Model |
---|---|
Engine power (gross) | 22.9 kW 31.2 hp |
Power take-off (PTO) power | 18.6 kW 25 hp |
Steering hydraulics | 15 L/min 4 gpm |
Implement hydraulics | 20.2 L/min 5.3 gpm |
Hitch type | Category 1 |
Lift capacity, 24-in. behind link arms | 615.1 kg 1356 lb |
Standard transmission; forward/reverse | Hydrostatic transmission (HST) |
Cruise control | Optional |
Approximate shipping weight (open-station; cab) | 1007.9 kg 2222 lb |
Wheelbase | 159.5 cm 62.8 in. |
Engine | |
Family | EYDXL1.64NDA FYDXL1.64NDA GYDXL1.64NDA |
Manufacturer | Yanmar |
Engine model | 3TNV88C-NJT |
Engine power (gross) | 22.9 kW 31.2 hp |
Power take-off (PTO) power | 18.6 kW 25 hp |
Rated engine speed | 2500 rpm |
Type | Diesel |
Injection pump type | High pressure common rail direct injection |
Aspiration | Natural |
Emissions compliance | Final Tier 4 |
Cylinders/displacement | 3 / 1.64 L 3 / 100.2 cu in. |
Number of cylinders | Three |
Cylinder liners | Cast-in-block |
Bore and stroke | 88 x 90 mm 3.46 x 3.54 in. |
Compression ratio | 19.1:1 |
Lubrication | Pressurized |
Cooling system | Water pump |
Air cleaner | Dual element |
Engine torque at rated speed | 87 Nm 64.2 lb-ft |
Fuel tank capacity | 28.5 L 7.5 U.S. gal. |
Electrical | |
Battery size | 500 CCA |
Alternator (12-V) | 55 amp |
Starter size | 1.4 kW 1.9 hp |
Fuel system | |
Type | High pressure common rail direct injection |
Fuel consumption | |
Transmission | |
Standard transmission; forward/reverse | Hydrostatic transmission (HST) |
Optional transmission; forward/reverse | |
Left-hand reverser | No |
Transmission gear ranges | |
Final drive | Bull Gear |
Brakes | Wet disc |
Steering | Power steering |
Clutch, wet/dry | |
Clutch disk diameter wet clutch | |
Axle capacity | Front 798 kg 1760 lb Rear 1197 kg 2640 lb |
Creeper | No |
Cruise control | Optional |
Differential lock | Yes |
Drawbar maximum vertical load | |
Hydraulics | |
Type | Open center |
Pump rated output | Steering 15 L/min 4 gpm Implement 20.2 L/min 5.3 gpm 35.2 L/min 9.3 gpm |
Pump type | Dual gear |
Maximum operating pressure | 172.4 bar 2500 psi |
Draft control sensing | Position control |
Remote control valves available | Up to two (optional) |
3-point hitch | |
Type | Category 1 |
Lift capacity, 24-in. behind link arms | 615.1 kg 1356 lb |
Power take-off (PTO) | |
Standard | 540 rpm at 2500 rpm |
Optional | |
Control | Independent |
Clutch | Wet disk |
Brake (for mid and rear PTO) | Wet disk |
Engagement method | |
Fluid capacities | |
Crankcase with filter | 4.5 L 4.8 qt |
Transmission and hydraulic system | |
Final drive | |
Type | Bull Gear |
Differential lock | |
Operator station | |
Rollover protective structure | Type Foldable ASABE S478 |
Platform - flat/straddle | Semi-flat |
Gear shift location - console/floor | Left-hand side |
Cab | |
Compliance | |
Visibility | |
Air conditioning, temperature differential | |
Doors | |
Noise rating | |
Seat equipment | |
Dimensions | |
Wheelbase | 159.5 cm 62.8 in. |
Front axle clearance | 36.3 cm 14.3 in. |
Turning radius with brakes | |
Turning radius without brakes | 2.9 m 9.4 ft |
Limited slip differential | |
Approximate shipping weight (open-station; cab) | 1007.9 kg 2222 lb |
Tires | |
Front | Farm - 7-14 Turf - 27x8.5-15 R4 - 25x8.5-14 R4 - 27x8.5-15 |
Rear | Farm - 11.2-24 Turf - 41x14-20 R4 - 15-19.5 R4 - 43x16-20 |
Front tread range | |
Rear tread spacing | |
Miscellaneous | |
Toolbox | |
Tilt steering wheel | |
12-V Outlet |
Accessories and Attachments
Ballast
Ballast Box - BW15073
The ballast box can be used to carry additional ballast for greater tractor stability.
A 23-cm (9-in.) high extension can be added to ballast box for even greater capacity.
The hitch utilizes a standard Category 1 configuration for connection to the tractor Category 1 hitch.
A bushing kit is required for the ballast box to be used with the iMatch™ Quick-Hitch.
The ballast box extension is only available through Parts; it is not a factory option.
Draft Link
Drawbar
Fits John Deere lawn and garden tow behind attachments.
- Strong magnetic grip
- Rust resistant
- Easy to install, secure fit
Ordering information
Customers, please contact your local John Deere dealer for availability and pricing information.
Magnetic hitch pin
Order number: LP63768
Rear Drawbar Kit - BLV10918
Engine
Attached to the engine cylinder block, the engine coolant heater plugs into a 120-V electrical outlet to warm the engine for fast cold-weather starts.
NOTE: It is recommended to install optional engine coolant heater, transmission oil heater, and battery heating pad (A22400P - ordered through A and I) if operating machine in temperatures below -18 ⁰C (0⁰F).
Radiator Clean Out Screen - BLV11022
Front Weights
Allows the operator to hang up to 10 weights on the tractor and retain them securely. This kit helps maintain stability when using rear 3-point hitch implements and a loader is not installed on the tractor. Proper ballast is essential for safety and to ensure the durability of the tractor components.
Allows the operator to hang up to 10 weights on the tractor and retain them securely. This kit helps maintain stability when using rear 3-point hitch implements and a loader is not installed on the tractor. Proper ballast is essential for safety and to ensure the durability of the tractor components.
Quik-Tatch Weight, 70 lb (32 kg) - LVU32113
Front Wheels And Tires
25 x 8.50 - 14 (6 PR, R4 Industrial, 2 Position) Front Wheels & Tires - BLV10851
27x8.5-15 (6PR R4 Industrial 2 Position) Front Wheels & Tires - BLV10862
27x8.50-15 (6PR, R3 Turf, 2 Position) Front Wheels & Tires - BLV10849
7-14 (6PR, R1 Bar, 2 Position) Front Wheels & Tires - BLV10860
Hydraulics
3E Series Tractors can be equipped with a field-installed rear hydraulic remote kit, providing two additional hydraulic spools on the back of the tractor. This kit can be field installed on a tractor with a loader or without a loader.
The functions are completely separate from the loader. These rear remotes can be hooked up to a wide variety of implements and attachments such as the following:
- Hydraulically angled blade
- Hydraulically controlled chute/spout on a 3-point hitch-mounted snow blower
- Hydraulic scarifiers on a box blade
- Many other hydraulic rear attachments
This versatile kit gives 3E Series Tractor operators the options they desire for putting their tractors into a wide range of tasks. The first spool is equipped with a float position, giving the operator the ability to contour the landscape and improve the final grade with certain implements.
Please note that neither of the spools in this kit are equipped with a detent position; therefore, they should not be hooked up to anything with a motor, as the valve was not designed to be run open. It is designed for momentary, on-demand hydraulic flow such as moving a cylinder.
The approximate installation time is 1 hour to 1.5 hours.
The power beyond kit allows access to pressurized hydraulic oil at the rear of the tractor for operating attachments equipped with an open center control valve, such as a backhoe and log splitter.
Lighting
This kit provides light to the rear of the tractor for evening work.
For open-station tractors only, this kit contains individual light.
Allow 30 minutes to install.
NOTE: Kit includes one rear light.
NOTE: Both the rear- and forward-work lights are compatible together and with the light-brush guard kits. The light kit contains a two-to-four pigtail that plugs into the main harness, as if only plugging one set of lights, providing two sets of plugs to use for forward and rear-work lights. The forward light is installed on top of the brush guard, and the rear light is installed inside the ROPS using the bolt holding the light and brush guard on.
NOTE: For 102E3 and 1026R Tractors – kit interference during backhoe operations (mounted inside ROPS) – use LVB25546 forward-light kit as an alternative.
The forward-lighting kit provides extra visibility when working in dark conditions. Lights attach to the brush guards located on the rollover protective structure (ROPS). Each kit contains two lights.
NOTE: Requires BLV10400 warning light brush guard kit and LVB26026 light kit harness. Not compatible with LVB25547 rear work light kit (1023E).
NOTE: Requires BLV10400 warning light brush guard kit. Not compatible with LVB25547 rear work light kit (1025R, 2025R, 2032R, 2038R, 3025E, 3032E, 3038E, 4105, 4044M, 4052M, 4066M).
NOTE: Requires BLV10620 premium warning light brush guard kit. Not compatible with LVB25547 rear work light kit (3033R, 3039R, 3046R, 4044R, 4052R, 4066R).
Rollover protective structure (ROPS) mounted LED work lights
An optional LED work light kit is available for all open-station compact utility tractors. These lights provide extra visibility when working in dark conditions and have 180-degree rotation to face forward or backward. The kit contains two lights and the mounting hardware required for installation.
This lighting kit is mounted to the warning light brush guard kit, which is mounted to the ROPS and requires attachment BLV10400 for installation.
The halogen work light kit attachment is still available (LVB25546).
ROPS warning-light brush guards protect turn signal/warning lights from damage caused by low branches on trees.
Two guards are included in each kit and are for open-operator station (OOS) tractors only.
ROPS warning-light brush guards protect turn signal/warning lights from damage caused by low branches on trees.
For open-station tractors only.
Two guards included in each kit.
Miscellaneous
Cruise Control Kit - BLV10898
Rear License Plate Kit (Includes Light) - BLV10924
- Provides necessary tractor parts to accept implement safety chains
- Attaches to tractor drawbar ahead of hitch pin
- Order safety chain from implement section
Tractor Cover - LP95637
Open Operator's Station
The canopy attaches to the rollover protective structure (ROPS) to protect the operator from inclement weather.
NOTE: Additional mounting brackets are required to adapt the canopy (LVB25334) to ROPS. See ordering information below.
The canopy attaches to the rollover protective structure (ROPS) to protect the operator from inclement weather.
For open-station tractors only.
NOTE: Additional mounting brackets are required to adapt the canopy (LVB25334) to ROPS. See ordering information below.
Large Seat Cover - LP95233
Left Hand Mirror Kit - BLV11034
Right Hand Mirror Kit - BLV11035
Provides the operator the necessary shade and protection from the elements.
- Attaches to the tractor's rollover protective structure (ROPS)
- For open-station tractors only
Power Take-off (Pto)
Rear Wheel Weights
Attaching Hardware for Rear Wheel Weight - BM19951
Attaching Hardware for Starter Rear Wheel Weight, 60 lb for 16 in. and 19.5 in. Wheel - BM19938
- Provide additional traction and stability
- Starter and additional weight for 15-in. wheel, 16.5-in. wheel, 17.5-in. wheel, and 19.5-in. wheel
- Up to three weights per wheel can be added
Rear Wheels And Tires
11.20-24 (6PR, R1 Bar, 1 Position) Rear Wheels & Tires - BLV10854
15-19.5 (6PR, R4 Industrial, 1 Position) Rear Wheels & Tires - BLV10852
41x14-20 (4PR, R3 Turf, 1 Position) Rear Wheels & Tires - BLV10850
43x16-20 (4PR, R4 Industrial, 2 Position) Rear Wheels & Tires - BLV10988
Provide added traction in snowy and icy conditions.
Provide added traction in snowy and icy conditions.
Three-point Hitch
3-Point Hitch Tractor Receiver Hitch - LP25001
iMatch Quick Hitch Bushings - LVU12858
One of the greatest operator concerns involves difficulty in attaching tractor implements. John Deere has addressed this issue with the iMatch Quick-Hitch.
The iMatch Quick-Hitch provides easy hookup and a guaranteed fit for all Category 1 implements designed to meet the ASAE Category 1 Standard S278.6 for quick-attach hitches.
- All implements require a set of bushings in order for the attachment to fit and work properly with the iMatch Quick-Hitch. One set of bushings comes with the iMatch Quick-Hitch.
NOTE: All implements (box blades, tillers, rear blades, landscape rakes, etc.) require a set of bushings to enlarge the pin to fit with the iMatch hooks. Bushings of different lengths can be found in the parts system or through a bushing supplier (see dimensions below).
- Upper bushing
- Inside diameter of 0.76 in. to 0.77 in. (19 mm to 20 mm)
- Outside diameter of 1.24 in. to 1.25 in. (31 mm to 32 mm)
- Lower bushings
- Inside diameter of 0.88 in. to 0.89 in. (22 mm to 23 mm)
- Outside diameter of 1.43 in. to 1.44 in. (36 mm to 37 mm)
iMatch Quick-Hitch dimensions
Dimensions designated | Millimeters (minimum) | Millimeters (maximum) |
'A' lower socket inside span | 686.56 | 689.61 |
'B' lower socket width | 27.94 | 29.46 |
'C' lower socket diameter | 38.1 | 38.61 |
'D' upper hook vertical spacing | 375.41 | 377.96 |
iMatch Quick-Hitch implement geometry
Dimensions designated | Millimeters (minimum) | Millimeters (maximum) |
'A' lower hitch pin or adapter outside diameter | 36.33 | 36.58 |
'B' lower hitch pin inner shoulder spread | 681.0 | 684.3 |
'C' lower hitch pin outer shoulder spread | 750.83 | 753.88 |
'D' lower hitch pin inner/outer shoulder diameter | 50.55 | 63.75 |
'E' coupler mast pin diameter | 31.50 | 31.75 |
'F' coupler mast pin vertical spacing | 379.48 | 382.53 |
Transmission
Weights
Reviews
52 reviews
- Filter
- Star Rating
- Value
- Quality