9R 540

Front supports (9R Wheel Tractor)

Front frame support (9RX Tractor)

Front frame and axle support kits provide additional support to the front frame and axle joint when the tractor is used in applications that put high torque and high vertical loads on the front end of the machine. This includes front-mounted liquid tanks and front 3-point hitches.
 
9RX Tractors
 
A front frame support kit is required on all 9RX Tractors with front-mounted liquid tanks or a front 3-point hitch. This kit enables operators to utilize the 9RX Tractors for supplemental crop nutrition application or for utilizing a rear 3-point hitch mounted sprayer. The front frame supports are standard on all 9RX Scraper Tractors.
 
Mounting of dozer blades
 
The mounting of dozer blades is approved on 9R and 9RX Tractors with 762-mm and 914-mm (30-in. and 36-in.) tracks. The mounting of dozer blades is not approved on 9RT and 9RX Tractors with 457-mm and 610-mm (18-in. and 24-in.) tracks.

• For all 9R and 9RX Tractors with 762-mm and 914-mm (30-in. and 36-in.) tracks, additional frame supports supplied by the dozer manufacturer are required.
• Follow manufacturer guidelines for mounting dozer blade components to the frame of the tractor.

Conjunto de suporte para tablet BRE10255 (1), conjunto de suporte para telefone celular BRE10015 (2) e suporte de montagem em forma de L RE343680 (3)

Conjunto de porta-copos com autonivelamento BRE10152

Conjunto de suporte de telefone celular com bloqueio por sucção BXE10606

Conjunto de suporte de tablet com bloqueio por sucção BXE10607

Conjunto de suporte para tablet BRE10255

Conjunto de suporte para tablet BXE10864

O suporte para tablet, telefone celular ou bebidas pode ser feito facilmente com estas soluções. Estas soluções robustas e fáceis de usar mantêm todos os itens importantes exatamente onde são desejados.

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

Conjunto de suporte para tablet BRE10255 (1), conjunto de suporte para telefone celular BRE10015 (2) e suporte de montagem em forma de L RE343680 (3)

Conjunto de porta-copos com autonivelamento BRE10152

Conjunto de suporte de telefone celular com bloqueio por sucção BXE10606

Conjunto de suporte de tablet com bloqueio por sucção BXE10607

Conjunto de suporte para tablet BRE10255

Conjunto de suporte para tablet BXE10864

O suporte para tablet, telefone celular ou bebidas pode ser feito facilmente com estas soluções. Estas soluções robustas e fáceis de usar mantêm todos os itens importantes exatamente onde são desejados.

Display GreenStar™ 3 2630 exibido

Use as tabelas abaixo para encontrar todas as peças necessárias para conectar os displays GreenStar™ fisicamente e eletronicamente.

Para displays GreenStar™ 2 2600 CommandCenter™/GreenStar™ 3 2630:

O suporte tipo abraçadeira com monitor GreenStar™ não é recomendado com o trilho vertical (BRE10575).

OBSERVAÇÃO: Encomende também o chicote elétrico (PF90686) e o cabo Ethernet (PFP12950). Também está disponível uma película protetora opcional para a tela (PF90596).

Para display universal 4240/4640 e monitor estendido:

O suporte tipo abraçadeira com monitor GreenStar™ não é recomendado com o trilho vertical (BRE10575).

OBSERVAÇÃO: Encomende também o chicote elétrico (PFP12435) e o cabo Ethernet (RE573617). Também está disponível uma película protetora opcional para a tela (PF90596).

BRE10501 CommandARM bracket

This unique bracket connects to the right side of the CommandARM. It is compatible with the cell phone mount (BRE10015), tablet mount (BRE10255), and more. It is also compatible with the touchscreen radio relocation kit (BXX11045) for Premium and Ultimate Comfort and Convenience packages.

The floor insulation kit can reduce cab heat generated by transmission and hydraulic oil temperatures below the cab floor. It can reduce the overall cab temperature, as it works as a thermal barrier. The product comes in a large sheet, which is easily cut to fit the contours of the cab floor.

The kit is large enough to fit the floor pan design of 6 through 9 Series Tractor cabs.

Foot decelerator next to pedals

BXX10810 foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

BRE10458 footrest kit with three pegs

Foot peg on the steering column

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with the extension and adjustment kit (BRE10511)

R562310 harness routing hook (shown mounted to headliner rail R558980 and using retention features of the C-post)

Harness routing hook

Keep accessory and monitor wiring neatly contained with these moveable harness hooks. These hooks are specifically designed to easily snap into the factory headliner rail and BRE10574 window mounting bracket and rail with no tools and can be moved as needed. These hooks allow accessory wiring to routed together for a clean look and maximized visibility.

RE584990 leather steering wheel

Close-up of leather steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

Conjunto de tirante AL212683 com placas de montagem

Conjunto de tirante de 117,6 mm PF80459

Suporte esférico de 38,1 mm PF80460 em parafuso em U

Conjunto de tirante de 76,2 mm RE574454 com esfera de 38,1 mm em placa de montagem redonda

Suporte esférico de 38,1 mm UC17356 em quadrado universal

Suporte esférico de 25,4 mm RE558821 em viga de 10 mm

Suporte de montagem de acessórios tipo abraçadeira AXE59372

Conjunto de suporte esférico com ranhura em T de 25,4 mm (esquerda) BRE10482 e conjunto de suporte esférico com ranhura em T de 38,1 mm BRE10483

Há uma variedade de soluções adicionais de peças de montagem disponíveis na John Deere para resolver necessidades específicas de configuração de montagem. A tabela abaixo inclui várias peças adicionais (não mostradas acima) para ajudar em diversas necessidades de montagem.

Display GreenStar™ 3 2630 exibido

Use as tabelas abaixo para encontrar todas as peças necessárias para conectar os displays GreenStar™ fisicamente e eletronicamente.

Para displays GreenStar™ 2 2600 CommandCenter™/GreenStar™ 3 2630:

O suporte tipo abraçadeira com monitor GreenStar™ não é recomendado com o trilho vertical (BRE10575).

OBSERVAÇÃO: Encomende também o chicote elétrico (PF90686) e o cabo Ethernet (PFP12950). Também está disponível uma película protetora opcional para a tela (PF90596).

Para display universal 4240/4640 e monitor estendido:

O suporte tipo abraçadeira com monitor GreenStar™ não é recomendado com o trilho vertical (BRE10575).

OBSERVAÇÃO: Encomende também o chicote elétrico (PFP12435) e o cabo Ethernet (RE573617). Também está disponível uma película protetora opcional para a tela (PF90596).

Refrigerator

Keep food and drinks cool with refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists, and no software is required to complete the install.

Conjunto BRE10574 com suporte de aço (A) e trilho de montagem (B)

Um suporte de aço grande, que abrange toda a janela do lado direito, é montado diretamente na estrutura da cabine para maior rigidez e resistência. O trilho de montagem do revestimento (incluído neste kit) é aparafusado no suporte de aço. Esta solução permite ao operador configurar e reconfigurar monitores e acessórios sem alterar as soluções de montagem, a partir de qualquer dos dois locais. Esse trilho acomoda soluções de montagem de tipo abraçadeira e ranhura em T (adquiridas separadamente).

• Abrange a janela inteira do lado direito.
• Utiliza o mesmo número de peça do trilho de montagem do revestimento de fábrica (R558980) para fácil reconfiguração dos acessórios.
• O trilho de montagem de alumínio é montado na parte superior ou inferior do suporte de aço, permitindo ainda mais opções e maximizando as preferências de visibilidade.
• Compatível com AXE59372 (suporte tipo abraçadeira) e BRE10482 e BRE10483 (suportes esféricos com ranhura em T).

Conjunto de suporte para tablet BRE10255 (1), conjunto de suporte para telefone celular BRE10015 (2) e suporte de montagem em forma de L RE343680 (3)

Conjunto de porta-copos com autonivelamento BRE10152

Conjunto de suporte de telefone celular com bloqueio por sucção BXE10606

Conjunto de suporte de tablet com bloqueio por sucção BXE10607

Conjunto de suporte para tablet BRE10255

Conjunto de suporte para tablet BXE10864

O suporte para tablet, telefone celular ou bebidas pode ser feito facilmente com estas soluções. Estas soluções robustas e fáceis de usar mantêm todos os itens importantes exatamente onde são desejados.

Trilho vertical curto BRE10575 (montado no poste dianteiro direito)

Trilho vertical curto (montado no poste traseiro direito inferior)

Trilho vertical curto (montado no poste C traseiro esquerdo)

Está disponível um trilho de montagem de alumínio mais curto, de 260 mm. O kit inclui todas as peças de fixação necessárias para montar em até cinco locais verticais, incluindo a estrutura de proteção na capotagem (EPC) do poste A direito superior e inferior, a EPC do poste C superior direito e a EPC do poste C superior traseiro esquerdo. É compatível com os suportes esféricos com abraçadeira e com ranhura em T (adquiridos separadamente).

• Até cinco locais verticais sustentados por este trilho (o kit contém um trilho e peças de fixação).
• Utiliza o mesmo formato de trilho de montagem do revestimento de fábrica para facilitar o ajuste e as preferências do operador.
• Funciona em combinação com outras soluções de suporte de acessórios.
• Compatível com AXE59372 (suporte tipo abraçadeira) e BRE10482 e BRE10483 (suportes esféricos com ranhura em T).

BRE10436 multifunction lever (shown in model year 2018 7R Tractor)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

RE275532 storage container

Storage container mounting location

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right-side window.

RE593670 sun shade shown

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

Conjunto de suporte para tablet BRE10255 (1), conjunto de suporte para telefone celular BRE10015 (2) e suporte de montagem em forma de L RE343680 (3)

Conjunto de porta-copos com autonivelamento BRE10152

Conjunto de suporte de telefone celular com bloqueio por sucção BXE10606

Conjunto de suporte de tablet com bloqueio por sucção BXE10607

Conjunto de suporte para tablet BRE10255

Conjunto de suporte para tablet BXE10864

O suporte para tablet, telefone celular ou bebidas pode ser feito facilmente com estas soluções. Estas soluções robustas e fáceis de usar mantêm todos os itens importantes exatamente onde são desejados.

R569171 door lock handle

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

ISO 11783 location in model year 2011 to 2020 R Series Tractor cab

ISO 11783 location in model year 2020 7R and 8R/8RT/8RX (with updated cab) and model year 2022 and newer 9R/9RT/9RX

RE322780 ISO cab implement CAN bus adapter

The ISO cab implement CAN bus adapter is available to connect any ISO compliant implement or device to an 8R, 8RT, 9R, 9RT, and 9RX (including Scraper Special) Tractor. These connectors are commonly used for planter frame control boxes. 

Refer to the operator's manual, sections 16 (CommandCenter™) and 25 (Operator Station), for additional information on ISO implements.

NOTE: If the harness is not in use, unplug it from the ISO 11783 location or plug the four-pin connectors together on the harness. If neither of these are done, implement CAN communication errors occur.

StarFire mounting bracket

The model year 2020 and newer large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or StarFire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

Ethernet cable

This cable connects the cornerpost Ethernet connector (square) to the GreenStar™ 3 2630 Display Ethernet connector (round). It is required for used with Remote Display Access (RDA), Wireless Data Transfer (WDT), and Machine Sync.

The square-to-round connector cable is 80-cm (31.5-in.) long.

Hydraulic hose support

This field-installed option reduces stress on the couplers by providing support to the heavy hydraulic hoses used in scraper application. The hydraulic hose support attaches to the back of the tractor next to the drawbar.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

Carpet floor mat

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

Foot throttle kit

Foot throttle next to pedals

BRE10440 foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

Foot decelerator kit

Foot decelerator next to pedals

BXX10810 foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

Footrests

BRE10458 footrest kit with three pegs

Foot peg on the steering column

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

Sun shade

RE593670 sun shade shown

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

Storage container with lid/ashtray

RE275532 storage container

Storage container mounting location

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

Leather-wrapped steering wheel

RE584990 leather steering wheel

Close-up of leather steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

Refrigerator

Refrigerator

Keep food and drinks cool with refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

Rearview mirror (internal)

RE588734 internal rear mirror (shown in standard mounting position)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

Cab power inverter

Type A/B style socket inverter kit (type C style is similar)

Cab power inverter kit

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

RE596958 complete John Deere power strip for model year 2020 and newer cabs

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

RE596959 power adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Antenna coax and power connector base prewired in the cab

Harness adapter for power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

Amp-to-flying leads power connector

RE37651 power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

Amp-to-John Deere power outlet adapter

RE67015 outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

External StarFire™ mounting bracket

StarFire mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

Front license plate mounting bracket

License plate mounting bracket (front)

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

Vandal protection door locks with custom key

R569171 door lock handle

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

Joystick (multifunction lever)

BRE10436 multifunction lever (shown in model year 2018 7R Tractor)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

Subwoofer and tweeter kit

Subwoofer

Tweeters

Amplifier

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

Touchscreen radio relocation kit

BXX11045 touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

Touchscreen video camera upgrade kit

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

Carpet floor mat

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

Foot throttle kit

Foot throttle next to pedals

BRE10440 foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

Foot decelerator kit

Foot decelerator next to pedals

BXX10810 foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

Footrests

BRE10458 footrest kit with three pegs

Foot peg on the steering column

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

Sun shade

RE593670 sun shade shown

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

Storage container with lid/ashtray

RE275532 storage container

Storage container mounting location

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

Leather-wrapped steering wheel

RE584990 leather steering wheel

Close-up of leather steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

Refrigerator

Refrigerator

Keep food and drinks cool with refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

Rearview mirror (internal)

RE588734 internal rear mirror (shown in standard mounting position)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

Cab power inverter

Type A/B style socket inverter kit (type C style is similar)

Cab power inverter kit

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

RE596958 complete John Deere power strip for model year 2020 and newer cabs

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

RE596959 power adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Antenna coax and power connector base prewired in the cab

Harness adapter for power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

Amp-to-flying leads power connector

RE37651 power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

Amp-to-John Deere power outlet adapter

RE67015 outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

External StarFire™ mounting bracket

StarFire mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

Front license plate mounting bracket

License plate mounting bracket (front)

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

Vandal protection door locks with custom key

R569171 door lock handle

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

Joystick (multifunction lever)

BRE10436 multifunction lever (shown in model year 2018 7R Tractor)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

Subwoofer and tweeter kit

Subwoofer

Tweeters

Amplifier

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

Touchscreen radio relocation kit

BXX11045 touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

Touchscreen video camera upgrade kit

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

9-pin electrical connector

The nine-pin electrical connector is required to allow TouchSet depth control to be used on implements with this feature. The harness provides a position input to the tractor selective control valve (SCV) unit that enables the TouchSet system.
 
This feature allows the operator to adjust height and depth of remote lift cylinders by using the TouchSet controls in the cab.

Type A/B style socket inverter kit (type C style is similar)

Cab power inverter kit

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

Carpet floor mat

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

Foot throttle kit

Foot throttle next to pedals

BRE10440 foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

Foot decelerator kit

Foot decelerator next to pedals

BXX10810 foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

Footrests

BRE10458 footrest kit with three pegs

Foot peg on the steering column

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

Sun shade

RE593670 sun shade shown

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

Storage container with lid/ashtray

RE275532 storage container

Storage container mounting location

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

Leather-wrapped steering wheel

RE584990 leather steering wheel

Close-up of leather steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

Refrigerator

Refrigerator

Keep food and drinks cool with refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

Rearview mirror (internal)

RE588734 internal rear mirror (shown in standard mounting position)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

Cab power inverter

Type A/B style socket inverter kit (type C style is similar)

Cab power inverter kit

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

RE596958 complete John Deere power strip for model year 2020 and newer cabs

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

RE596959 power adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Antenna coax and power connector base prewired in the cab

Harness adapter for power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

Amp-to-flying leads power connector

RE37651 power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

Amp-to-John Deere power outlet adapter

RE67015 outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

External StarFire™ mounting bracket

StarFire mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

Front license plate mounting bracket

License plate mounting bracket (front)

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

Vandal protection door locks with custom key

R569171 door lock handle

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

Joystick (multifunction lever)

BRE10436 multifunction lever (shown in model year 2018 7R Tractor)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

Subwoofer and tweeter kit

Subwoofer

Tweeters

Amplifier

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

Touchscreen radio relocation kit

BXX11045 touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

Touchscreen video camera upgrade kit

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

Heavy-duty gudgeon

The heavy-duty gudgeon is designed for increased loads over the standard gudgeon through larger steering pins and tapered roller bearings. This heavy-duty upgrade increases the durability and strength of the gudgeon and is base equipment on Scraper Special and all 9RX Tractors.

Tow cable front hook

The tow cable is recommended for pulling all 9 Series Tractors in time of needed assistance. Tow cables are available as a factory-installed option on all ag tractors and are base equipment on all Scraper Special Tractors. The tow cable attaches to the rear of the tractor frame, and the quick access connection point is mounted in the front of the tractor.

Tow cable front hook

The tow cable is recommended for pulling all 9 Series Tractors in time of needed assistance. Tow cables are available as a factory-installed option on all ag tractors and are base equipment on all Scraper Special Tractors. The tow cable attaches to the rear of the tractor frame, and the quick access connection point is mounted in the front of the tractor.

1.3-cm (½-in.) coupler options

Additional 140-L/min (37-gpm) standard flow SCVs with 1.3-cm (1/2-in.) couplers can be field-installed for those who need to control additional hydraulic functions. Kits include ISO lever-assisted breakaway couplers and armrest control lever.

Reference the table below for kit options to add a fifth, sixth, or seventh and eighth SCV.

1.9-cm (¾-in.) coupler options

1.9-cm (¾-in.) SCV coupler kit

1.9-cm (¾-in.) SCV coupler kit (BRE10107 shown)

For greater versatility, producers can replace one 140-L/min (37-gpm) standard flow SCV and 1.3-cm (½-in.) coupler with this 159-L/min (42-gpm) high-flow SCV and 1.9-cm (¾-in.) coupler.

1.9-cm (¾-in.) coupler adapter conversion

BRE10486 1.9-cm (3/4-in.) coupler and adapter (two kits shown stacked)

The conversion design is exclusive to John Deere and converts the couplers on a standard flow SCV from 1.3-cm (½-in.) couplers to 1.9-cm (¾-in.) couplers (with a maximum of 140 L/min [37 gpm]). This kit is ideal for operators with:

• High hydraulic demand implements, such as large air seeders and planters
• Implements that require 1.9-cm (¾-in.) couplers
• A desire to improve implement raise/lower cycle times for faster headland turns

This conversion is an economical solution to improve the transfer of hydraulic horsepower from the tractor to the implement.

• Converted SCV could benefit from a decreased pressure drop range from 2.1 to 9 bar (30 to 130 psi)*, depending on the implement.
  • *NOTE: Based on internal testing.
• Installation does not require removing the SCV stack.
• No software updates are required.

Seeding hydraulic Intelligent Power Management (IPM) kit

SCV connections in a stack configuration

The seeding hydraulic IPM kit adds three 1.9-cm (¾-in.) hydraulic couplers with 159-L/min (42-gpm) high-flow SCVs onto the rear of the machine to supplement the additional hydraulic power and flow consumed by systems running dual fan motors such as the Air Power™ 2 system equipped on John Deere C850 Air Carts.

Also provided in the kit is a software enhancement for controlled power increase of up to 18.6 engine kW (25 engine hp) at 2100 rpm and “power limited” in gears 5 through 18 and 37.3 engine kW (50 engine hp) in gears 1 through 4. Power increase is only provided when required.

 Field installed kit includes:

• Three 1.9-cm (¾-in.) couplers
• Three 159-L/min (42-gpm) SCV sections
• Mounting bracket
• Steel hydraulic lines
• All necessary hardware
• Software update (via download on Custom Performance)

For the complete description of the capabilities of this kit, please see the seeding hydraulic IPM feature which provides the factory-installed option code for this same system.

1.3-cm (½-in.) coupler options

Additional 140-L/min (37-gpm) standard flow SCVs with 1.3-cm (1/2-in.) couplers can be field-installed for those who need to control additional hydraulic functions. Kits include ISO lever-assisted breakaway couplers and armrest control lever.

Reference the table below for kit options to add a fifth, sixth, or seventh and eighth SCV.

1.9-cm (¾-in.) coupler options

1.9-cm (¾-in.) SCV coupler kit

1.9-cm (¾-in.) SCV coupler kit (BRE10107 shown)

For greater versatility, producers can replace one 140-L/min (37-gpm) standard flow SCV and 1.3-cm (½-in.) coupler with this 159-L/min (42-gpm) high-flow SCV and 1.9-cm (¾-in.) coupler.

1.9-cm (¾-in.) coupler adapter conversion

BRE10486 1.9-cm (3/4-in.) coupler and adapter (two kits shown stacked)

The conversion design is exclusive to John Deere and converts the couplers on a standard flow SCV from 1.3-cm (½-in.) couplers to 1.9-cm (¾-in.) couplers (with a maximum of 140 L/min [37 gpm]). This kit is ideal for operators with:

• High hydraulic demand implements, such as large air seeders and planters
• Implements that require 1.9-cm (¾-in.) couplers
• A desire to improve implement raise/lower cycle times for faster headland turns

This conversion is an economical solution to improve the transfer of hydraulic horsepower from the tractor to the implement.

• Converted SCV could benefit from a decreased pressure drop range from 2.1 to 9 bar (30 to 130 psi)*, depending on the implement.
  • *NOTE: Based on internal testing.
• Installation does not require removing the SCV stack.
• No software updates are required.

Seeding hydraulic Intelligent Power Management (IPM) kit

SCV connections in a stack configuration

The seeding hydraulic IPM kit adds three 1.9-cm (¾-in.) hydraulic couplers with 159-L/min (42-gpm) high-flow SCVs onto the rear of the machine to supplement the additional hydraulic power and flow consumed by systems running dual fan motors such as the Air Power™ 2 system equipped on John Deere C850 Air Carts.

Also provided in the kit is a software enhancement for controlled power increase of up to 18.6 engine kW (25 engine hp) at 2100 rpm and “power limited” in gears 5 through 18 and 37.3 engine kW (50 engine hp) in gears 1 through 4. Power increase is only provided when required.

 Field installed kit includes:

• Three 1.9-cm (¾-in.) couplers
• Three 159-L/min (42-gpm) SCV sections
• Mounting bracket
• Steel hydraulic lines
• All necessary hardware
• Software update (via download on Custom Performance)

For the complete description of the capabilities of this kit, please see the seeding hydraulic IPM feature which provides the factory-installed option code for this same system.

Five remote SCVs

The field-installed electronic SCV kits are made available for tractors needing additional SCVs. These kits provide metered flow rates and timed detents with pressure and load sense compensation. The additional SCV(s) can also be integrated into the Headland Management System.
 
The field-installed kit includes International Organization for Standardization (ISO) lever-assisted breakaway couplers and armrest control lever.

1.3-cm (½-in.) coupler options

Additional 140-L/min (37-gpm) standard flow SCVs with 1.3-cm (1/2-in.) couplers can be field-installed for those who need to control additional hydraulic functions. Kits include ISO lever-assisted breakaway couplers and armrest control lever.

Reference the table below for kit options to add a fifth, sixth, or seventh and eighth SCV.

1.9-cm (¾-in.) coupler options

1.9-cm (¾-in.) SCV coupler kit

1.9-cm (¾-in.) SCV coupler kit (BRE10107 shown)

For greater versatility, producers can replace one 140-L/min (37-gpm) standard flow SCV and 1.3-cm (½-in.) coupler with this 159-L/min (42-gpm) high-flow SCV and 1.9-cm (¾-in.) coupler.

1.9-cm (¾-in.) coupler adapter conversion

BRE10486 1.9-cm (3/4-in.) coupler and adapter (two kits shown stacked)

The conversion design is exclusive to John Deere and converts the couplers on a standard flow SCV from 1.3-cm (½-in.) couplers to 1.9-cm (¾-in.) couplers (with a maximum of 140 L/min [37 gpm]). This kit is ideal for operators with:

• High hydraulic demand implements, such as large air seeders and planters
• Implements that require 1.9-cm (¾-in.) couplers
• A desire to improve implement raise/lower cycle times for faster headland turns

This conversion is an economical solution to improve the transfer of hydraulic horsepower from the tractor to the implement.

• Converted SCV could benefit from a decreased pressure drop range from 2.1 to 9 bar (30 to 130 psi)*, depending on the implement.
  • *NOTE: Based on internal testing.
• Installation does not require removing the SCV stack.
• No software updates are required.

Seeding hydraulic Intelligent Power Management (IPM) kit

SCV connections in a stack configuration

The seeding hydraulic IPM kit adds three 1.9-cm (¾-in.) hydraulic couplers with 159-L/min (42-gpm) high-flow SCVs onto the rear of the machine to supplement the additional hydraulic power and flow consumed by systems running dual fan motors such as the Air Power™ 2 system equipped on John Deere C850 Air Carts.

Also provided in the kit is a software enhancement for controlled power increase of up to 18.6 engine kW (25 engine hp) at 2100 rpm and “power limited” in gears 5 through 18 and 37.3 engine kW (50 engine hp) in gears 1 through 4. Power increase is only provided when required.

 Field installed kit includes:

• Three 1.9-cm (¾-in.) couplers
• Three 159-L/min (42-gpm) SCV sections
• Mounting bracket
• Steel hydraulic lines
• All necessary hardware
• Software update (via download on Custom Performance)

For the complete description of the capabilities of this kit, please see the seeding hydraulic IPM feature which provides the factory-installed option code for this same system.

Five remote SCVs

The field-installed electronic SCV kits are made available for tractors needing additional SCVs. These kits provide metered flow rates and timed detents with pressure and load sense compensation. The additional SCV(s) can also be integrated into the Headland Management System.
 
The field-installed kit includes International Organization for Standardization (ISO) lever-assisted breakaway couplers and armrest control lever.

Auxiliary hitch lift assist kit

Auxiliary hitch lift assist

Lift assist wheels are often used with heavy 3-point hitch-mounted implements. The hitch auxiliary raise kit provides hydraulic power for use with the lift assist wheels. Turning and transport are made easier using this feature.

Auxiliary hydraulic couplers

Auxiliary hydraulic couplers

When attaching implement hydraulic hoses to locations on the tractor other than into a selective control valve (SCV), it has always been a challenge to know what kits are required for compatibility. To assist in hooking up planters, seeders, and harvesting equipment where multiple connections are required, auxiliary hydraulic couplers can be added.

Hydraulic motor return couplers

The hydraulic motor return couplers can be used as a coupler for return oil flow from hydraulic orbital motors and other devices to the tractor's low-pressure return port, labeled ''R'' on the tractor.

Use of this connector specifically in the return to sump port position is for hydraulic components that require a ''leak-off line'' connection to the tractor. Components and implements that require this typically are larger orbital motors that require a drain for seal protection. The connector in the sump port is not to be used to carry return flow from a function to the tractor.

Power beyond couplers

Power beyond provides live hydraulic power to equipment. This kit supplies oil pressure to implements when the engine is running.
 
Any implement using power beyond must have a way to control oil flow. Use an independent control valve that is pressure-and-flow compensating (supplied separately) to control the oil flow rate from this coupler set.

Auxiliary hydraulic couplers

Auxiliary hydraulic couplers

When attaching implement hydraulic hoses to locations on the tractor other than into a selective control valve (SCV), it has always been a challenge to know what kits are required for compatibility. To assist in hooking up planters, seeders, and harvesting equipment where multiple connections are required, auxiliary hydraulic couplers can be added.

Hydraulic motor return couplers

The hydraulic motor return couplers can be used as a coupler for return oil flow from hydraulic orbital motors and other devices to the tractor's low-pressure return port, labeled ''R'' on the tractor.

Use of this connector specifically in the return to sump port position is for hydraulic components that require a ''leak-off line'' connection to the tractor. Components and implements that require this typically are larger orbital motors that require a drain for seal protection. The connector in the sump port is not to be used to carry return flow from a function to the tractor.

Power beyond couplers

Power beyond provides live hydraulic power to equipment. This kit supplies oil pressure to implements when the engine is running.
 
Any implement using power beyond must have a way to control oil flow. Use an independent control valve that is pressure-and-flow compensating (supplied separately) to control the oil flow rate from this coupler set.

Auxiliary hydraulic couplers

Auxiliary hydraulic couplers

When attaching implement hydraulic hoses to locations on the tractor other than into a selective control valve (SCV), it has always been a challenge to know what kits are required for compatibility. To assist in hooking up planters, seeders, and harvesting equipment where multiple connections are required, auxiliary hydraulic couplers can be added.

Hydraulic motor return couplers

The hydraulic motor return couplers can be used as a coupler for return oil flow from hydraulic orbital motors and other devices to the tractor's low-pressure return port, labeled ''R'' on the tractor.

Use of this connector specifically in the return to sump port position is for hydraulic components that require a ''leak-off line'' connection to the tractor. Components and implements that require this typically are larger orbital motors that require a drain for seal protection. The connector in the sump port is not to be used to carry return flow from a function to the tractor.

Power beyond couplers

Power beyond provides live hydraulic power to equipment. This kit supplies oil pressure to implements when the engine is running.
 
Any implement using power beyond must have a way to control oil flow. Use an independent control valve that is pressure-and-flow compensating (supplied separately) to control the oil flow rate from this coupler set.

Auxiliary light kit

Auxiliary light kit

A rear fender, rear-facing work light is available for the tractor. The kit comes with mounting hardware and a harness which directly connects to the tractor’s existing chassis harness.
 
This mounting location allows for illumination of the hitch and drawbar area to aid in making connections to implements when natural lighting conditions are poor.

BRE10445 cab roof work lighting - shown from left rear corner

Increase light output over halogen work lights with this four-light kit for the front and rear roof corners of the cab. These lights are the same parts included in the Premium and Ultimate Visibility package and are a plug-and-play update. Eliminate bulb replacements while increasing color temperature and lumen output with this eight-light LED upgrade.

RE588734 internal rear mirror (shown in standard mounting position)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

44.5-mm (1.75-in.), 1000-rpm PTO

PTO and shield

• Available on all 9R and 9RT Ag Tractors regardless of transmission.
• Full-power capability for maximum utilization (9R Tractors derate to 238 PTO kW [319 PTO hp] when tractor is stationary)
• 44.5-mm (1.75-in.) diameter shaft

Electrohydraulic PTO control

The 9R Tractors utilize an electrohydraulic PTO engagement switch to activate the optional 1000-rpm PTO.

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

Subwoofer

Tweeters

Amplifier

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

Quik-Hitch coupler

The hitch/coupler allows for quick, no-hassle hookups to many popular integral implements.

Features include:

• Tubular and box-welded steel construction
• Heat-treated bushings to prevent cracking and breakage
• Heat-treated hooks for long wear life
• Locking handles that rotate 100 degrees to open the locking lugs for easy implement release
• Hardened and zinc-plated steel alloy pins to take the shock of heavy loads and withstand exposure to the elements

Kit de conversão

O kit de conversão da barra de tração de categoria 5 para categoria 4 está disponível para produtores com implementos de categoria 4 que não podem ser convertidos para categoria 5.

O método preferencial durante a operação de tratores de alta potência é converter os implementos para a categoria 5.

Para informações adicionais sobre implementos, consulte as informações relativas à plantação e semeadura ou cultivo.

Quik-Hitch coupler

The hitch/coupler allows for quick, no-hassle hookups to many popular integral implements.

Features include:

• Tubular and box-welded steel construction
• Heat-treated bushings to prevent cracking and breakage
• Heat-treated hooks for long wear life
• Locking handles that rotate 100 degrees to open the locking lugs for easy implement release
• Hardened and zinc-plated steel alloy pins to take the shock of heavy loads and withstand exposure to the elements

Rear hitch pin joints on 9R and 9RT Tractors

The 9R/9RT rear hitch has pin joints located in the top lift carrier that uses dry joint pins (R304684).

Rear hitch pin joints on 7R, 8R, and 8RT Tractors

The 7R/8R/8RT rear hitch has pin joints located in six locations of the rear hitch that use dry joint pins (R169163).

The dry joint pins and balls can wear over time and require replacing to restore smooth operation. The heavy-duty greaseable pin kit provides a grease zerk fitting on each upper pin so that lubricating these pins becomes possible. Greasing should be performed weekly using the same grease used in the regular weekly greasing maintenance schedule as shown in the operator’s manual.

These kits allow for the pin replacement to last longer than the standard installed pin so long as it is regularly greased. This update reduces the need for future pin replacement in this joint.

Add a trailer brake system into the machine to safely and correctly connect the implement’s braking system. This kit allows operators to slow the tractor and the implement together, which is especially helpful for heavy road transport and to manage larger implements while maintaining good stopping power.
 

Always follow correct service intervals and perform required maintenance on the implement braking system by following the implement operator’s manual.

Wheel and four-track mounting bracket

Two-track mounting bracket

Dual-beam radar sensor

See your true ground speed by adding a dual-beam radar. Select the correct mounting bracket for the tractor based on the drivetrain configuration, which includes a perfect fit bracket, harness, and hardware.

Wheel and four-track mounting bracket

Two-track mounting bracket

Dual-beam radar sensor

See your true ground speed by adding a dual-beam radar. Select the correct mounting bracket for the tractor based on the drivetrain configuration, which includes a perfect fit bracket, harness, and hardware.

Front weights provide additional ballast for the front axle

Front support with suitcase weights

Cast Quik-Tatch suitcase weights (R127764) can be added to provide additional ballast for implements that exert heavy draft loads and require additional ballast or with hitch-mounted implements that require additional ballast to maintain steering control while transporting.

These weights are Quik-Tatch weights that require minimal effort to attach.

Pickup weights

Pickup weights

Pickup weights are designed to add fast weight to the tractor. The following pickup weights can be mounted at the front.

Support (base weight):

• 900-kg (1948-lb) pickup weight
• 1150-kg (2535.3-lb) pickup weight

All pickup hitches can also be mounted at the rear in the 3-point hitch as a counter weight. To use the third mounting point, an additional center-link bracket is available.

1500-kg (3307-lb) and 1800-kg (3968.3-lb) pickup weights

The two weights differ only internally, therefore no external differences are visible.

The pickup weights can either be installed on the rear hitch or on the front hitch of the tractor using the center-link bracket. They cannot be mounted directly on the front base weight. A front hitch is required. The center-link bracket for installation is included.

The shape of the 1500-kg (3307-lb) and 1800-kg (3968.3-lb) pick-up weights allows for quick and safe mounting. This is ensured by an optimal alignment of the weight and the tractor along with a self-centering design.

Major benefits of the design:

• Easy and comfortable
• Less time is required
• Lower risk of injury

Due to the user-friendliness, an optimal ballasting of the tractor is guaranteed at any time.

The performance of the tractor is used to a greater extent, which leads to higher productivity and a reduction in fuel consumption.

The weights cannot be front installed in combination with Quik-Tatch front weights.

NOTE: Ballast should be limited by the lowest of either tire capacity or tractor capacity. The carrying capacity of each tire should not be exceeded. For more ballasting information refer to the Operator's Manual and ballast calculator.

Front weights provide additional ballast for the front axle

Front support with suitcase weights

Cast Quik-Tatch suitcase weights (R127764) can be added to provide additional ballast for implements that exert heavy draft loads and require additional ballast or with hitch-mounted implements that require additional ballast to maintain steering control while transporting.

These weights are Quik-Tatch weights that require minimal effort to attach.

Pickup weights

Pickup weights

Pickup weights are designed to add fast weight to the tractor. The following pickup weights can be mounted at the front.

Support (base weight):

• 900-kg (1948-lb) pickup weight
• 1150-kg (2535.3-lb) pickup weight

All pickup hitches can also be mounted at the rear in the 3-point hitch as a counter weight. To use the third mounting point, an additional center-link bracket is available.

1500-kg (3307-lb) and 1800-kg (3968.3-lb) pickup weights

The two weights differ only internally, therefore no external differences are visible.

The pickup weights can either be installed on the rear hitch or on the front hitch of the tractor using the center-link bracket. They cannot be mounted directly on the front base weight. A front hitch is required. The center-link bracket for installation is included.

The shape of the 1500-kg (3307-lb) and 1800-kg (3968.3-lb) pick-up weights allows for quick and safe mounting. This is ensured by an optimal alignment of the weight and the tractor along with a self-centering design.

Major benefits of the design:

• Easy and comfortable
• Less time is required
• Lower risk of injury

Due to the user-friendliness, an optimal ballasting of the tractor is guaranteed at any time.

The performance of the tractor is used to a greater extent, which leads to higher productivity and a reduction in fuel consumption.

The weights cannot be front installed in combination with Quik-Tatch front weights.

NOTE: Ballast should be limited by the lowest of either tire capacity or tractor capacity. The carrying capacity of each tire should not be exceeded. For more ballasting information refer to the Operator's Manual and ballast calculator.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

36-kg (79-lb) starter weight R311921

36-kg (79-lb) starter weight R311921 – two track weight (inner and outer face shown)

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

72-kg (159-lb) weight R167153

72-kg (159-lb) weight R167153 (inner and outer face shown)

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

205-kg (452-lb) wheel weight R207782

205-kg (452-lb) wheel weight R207782 (inner and outer face shown)

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

70-kg (154-lb) starter weight R569392

70-kg (154-lb) starter weight R569392 (inner and outer face shown)

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

530-kg (1169-lb) rear wheel weight R563576

530-kg (1169-lb) rear wheel weight R563576 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

550-kg (1213-lb) wheel weight R563214

550-kg (1213-lb) wheel weight R563214 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

620-kg (1367-lb) wheel weight R563212

625-kg (1378-lb) wheel weight R553540 (inner and outer face shown)

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

900-kg (1984-lb) wheel weight R341378

900-kg (1984-lb) wheel weight R341378 (inner and outer face shown)

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Mounting kit BRE10026

Mounting kit BRE10026 (complete kit shown)

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

Idler weight TR110515 (shown with also order hardware)

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

36-kg (79-lb) starter weight R311921

36-kg (79-lb) starter weight R311921 – two track weight (inner and outer face shown)

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

72-kg (159-lb) weight R167153

72-kg (159-lb) weight R167153 (inner and outer face shown)

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

205-kg (452-lb) wheel weight R207782

205-kg (452-lb) wheel weight R207782 (inner and outer face shown)

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

70-kg (154-lb) starter weight R569392

70-kg (154-lb) starter weight R569392 (inner and outer face shown)

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

530-kg (1169-lb) rear wheel weight R563576

530-kg (1169-lb) rear wheel weight R563576 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

550-kg (1213-lb) wheel weight R563214

550-kg (1213-lb) wheel weight R563214 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

620-kg (1367-lb) wheel weight R563212

625-kg (1378-lb) wheel weight R553540 (inner and outer face shown)

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

900-kg (1984-lb) wheel weight R341378

900-kg (1984-lb) wheel weight R341378 (inner and outer face shown)

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Mounting kit BRE10026

Mounting kit BRE10026 (complete kit shown)

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

Idler weight TR110515 (shown with also order hardware)

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

36-kg (79-lb) starter weight R311921

36-kg (79-lb) starter weight R311921 – two track weight (inner and outer face shown)

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

72-kg (159-lb) weight R167153

72-kg (159-lb) weight R167153 (inner and outer face shown)

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

205-kg (452-lb) wheel weight R207782

205-kg (452-lb) wheel weight R207782 (inner and outer face shown)

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

70-kg (154-lb) starter weight R569392

70-kg (154-lb) starter weight R569392 (inner and outer face shown)

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

530-kg (1169-lb) rear wheel weight R563576

530-kg (1169-lb) rear wheel weight R563576 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

550-kg (1213-lb) wheel weight R563214

550-kg (1213-lb) wheel weight R563214 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

620-kg (1367-lb) wheel weight R563212

625-kg (1378-lb) wheel weight R553540 (inner and outer face shown)

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

900-kg (1984-lb) wheel weight R341378

900-kg (1984-lb) wheel weight R341378 (inner and outer face shown)

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Mounting kit BRE10026

Mounting kit BRE10026 (complete kit shown)

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

Idler weight TR110515 (shown with also order hardware)

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

36-kg (79-lb) starter weight R311921

36-kg (79-lb) starter weight R311921 – two track weight (inner and outer face shown)

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

72-kg (159-lb) weight R167153

72-kg (159-lb) weight R167153 (inner and outer face shown)

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

205-kg (452-lb) wheel weight R207782

205-kg (452-lb) wheel weight R207782 (inner and outer face shown)

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

70-kg (154-lb) starter weight R569392

70-kg (154-lb) starter weight R569392 (inner and outer face shown)

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

530-kg (1169-lb) rear wheel weight R563576

530-kg (1169-lb) rear wheel weight R563576 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

550-kg (1213-lb) wheel weight R563214

550-kg (1213-lb) wheel weight R563214 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

620-kg (1367-lb) wheel weight R563212

625-kg (1378-lb) wheel weight R553540 (inner and outer face shown)

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

900-kg (1984-lb) wheel weight R341378

900-kg (1984-lb) wheel weight R341378 (inner and outer face shown)

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Mounting kit BRE10026

Mounting kit BRE10026 (complete kit shown)

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

Idler weight TR110515 (shown with also order hardware)

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

36-kg (79-lb) starter weight R311921

36-kg (79-lb) starter weight R311921 – two track weight (inner and outer face shown)

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

72-kg (159-lb) weight R167153

72-kg (159-lb) weight R167153 (inner and outer face shown)

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

205-kg (452-lb) wheel weight R207782

205-kg (452-lb) wheel weight R207782 (inner and outer face shown)

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

70-kg (154-lb) starter weight R569392

70-kg (154-lb) starter weight R569392 (inner and outer face shown)

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

530-kg (1169-lb) rear wheel weight R563576

530-kg (1169-lb) rear wheel weight R563576 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

550-kg (1213-lb) wheel weight R563214

550-kg (1213-lb) wheel weight R563214 (inner and outer face shown)

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

620-kg (1367-lb) wheel weight R563212

625-kg (1378-lb) wheel weight R553540 (inner and outer face shown)

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

900-kg (1984-lb) wheel weight R341378

900-kg (1984-lb) wheel weight R341378 (inner and outer face shown)

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Mounting kit BRE10026

Mounting kit BRE10026 (complete kit shown)

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

Idler weight TR110515 (shown with also order hardware)

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.